Alaram and remote start intall guide - GM Forum - Buick, Cadillac, Chev, Olds, GMC & Pontiac chat


Audio (and aftermarket electronics) This is your place for alarms, remote starters, to brag about your system, exaggerate your db levels, or simply ask questions for stock or aftermarket audio. No Flames! (except from roasted amps)

Reply
 
 
 
Thread Tools Search this Thread
Old 07-03-2009, 01:26 PM   #1
Member
Posts like a V-Tak
Thread Starter
 
cincygoat's Avatar
 
Join Date: Feb 2009
Location: Amelia, OH
Posts: 99
Thanks: 0
Thanked 0 Times in 0 Posts
cincygoat is on a distinguished road
Default Alaram and remote start intall guide

Ok so this not a full write up but some helpful links and tips to install an Alarm or Remote Start or a combo
You will need an array of tools
Screw Drivers Standard and Phillips
Ratchet and 10mm Socket
Drill and drill bits (Bits must be able to drill through metal)
Old metal hanger or fish tape
Wire strippers and Razor Blade
Test light or volt meter (I prefer just a test light)
Soldering Iron, Flux and Solder
Heat Shrink Tubing (Harbor Freight)
Electrical Tape
Mounting Tape
Self tapping screws
Start out by removing the large trim piece that stretches from left of the steering wheel to around the heater controls and radio. (It just pulls off) Then remove the trim piece just below the steering wheel (4 10MM BOLTS)

Notice that after removing the trim piece that there is a piece of Styrofoam mounted to the back of it remove that and use the mounting tape to mount the unit here
After removing the piece you should have full access to all the vital wiring of the car and should look like this

Please be careful to not cut the bright yellow wire in the middle of the pic this is for your airbag
Now you need to expose some more wiring locations

This area will let you splice into your power locks and door trigger (door trigger activates your interior lights)
Note: The wiring diagrams say that the tan wire is the driverí* door and the dark blue wire is for the rest of the doors. I had a trouble getting these to work so for my 96 SE the white wire activates the lights when any door is open.
The way to test this is to close the latch on the door using a screw driver

On my 96 and like year Bonnevilleí* the white wire we are talking about will trigger the test light when all the doors are closed and will turn the test light off when a door is open.
Also connecting wires and splicing into wires it is very important to do a good job of covering any loose wires although I use soldering and heat shrink tubing there are other safe ways to do this
One more area of wiring to expose and this area you will find you trunk wire and your parking lights

This isnít a very good picture for locating the area this is just right next to the driverí* seat pull out some trim and pull back the carpet
At some point you will need to get wires into the engine bay behind the drivers strut tower there is a rubber grommet on the fire wall use you metal hanger or fish tape to get the wire into the engine bay

Once again this is just how I do it if you would rather drill a hole in the fire wall and put in a new rubber grommet than by all means do so
Mounting the siren is just a matter of choice on location I mounted mine here (use self tapping screws)

The drill will also be used to install a hood pin switch if you cannot find and existing whole then make a new one.
You will also have to find the tach output for remote start installations this is a purple and white wire

Remove the engine cover and you will find this just to the right of the coil packs
Also with remote start installs you will be required to wire in a relay and you will be cutting into some very important wiring I strongly suggest soldering here if you donít know how find someone who does
The following links will tell you the color of the wires specific to your year make and model
Page 1
Page 2
I hope this helps if anyone plans on doing this and needs help just pm me
cincygoat is offline   Reply With Quote
Old 07-03-2009, 01:49 PM   #2
Retired Senior Admin

Expert Gearhead
 
Danthurs's Avatar
 
Join Date: May 2006
Location: Sheboygan Wisconsin
Posts: 29,661
Thanks: 0
Thanked 16 Times in 13 Posts
Danthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to all
Default

Nice, mind if I move that to electrical?
Danthurs is offline   Reply With Quote
Old 07-03-2009, 02:01 PM   #3
Member
Posts like a V-Tak
Thread Starter
 
cincygoat's Avatar
 
Join Date: Feb 2009
Location: Amelia, OH
Posts: 99
Thanks: 0
Thanked 0 Times in 0 Posts
cincygoat is on a distinguished road
Default

go ahead
cincygoat is offline   Reply With Quote
Old 07-03-2009, 02:08 PM   #4
Retired Senior Admin

Expert Gearhead
 
Danthurs's Avatar
 
Join Date: May 2006
Location: Sheboygan Wisconsin
Posts: 29,661
Thanks: 0
Thanked 16 Times in 13 Posts
Danthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to allDanthurs is a name known to all
Default

All done. I changed how the pictures are handled. Good work, you now have a writeup in tech info.
Danthurs is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
OBD-II Trouble shooting guide 1997-99 START HERE Danthurs OBD-II Trouble Shooting 0 09-22-2009 11:45 PM
Alaram and remote start intall guide cincygoat Electrical 0 07-03-2009 01:26 PM
Keyless Entry/Remote Start Remote Compatibility wjcollier07 Lounge 0 02-08-2008 11:37 AM
uninstall 1989 bonni stereo to intall into 1995 bonni base1001 Audio (and aftermarket electronics) 8 10-06-2006 06:32 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 04:33 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.