Po171 Chevy Express
Senior Member
True Car Nut
Joined: Feb 2015
Posts: 6,849
Likes: 1,014
From: Earth
New Delphi MAF has been installed and it’* still lean, but maybe slightly less so.
the new sensor does seem to have helped, it’* not quite as lean as it used to be. LTFT are usually between 10-15%, lowest when accelerating from a stop, sometimes 7-8%, and highest when maintaining about 35-45 mph, at about 15%. At idle about 11-12%or so. The biggest difference is when I start coasting it no longer jumps 5-15%, now only maybe 2%. Everything else on the live data looks fine except the downstream o2 sensors are both still reading 99.2%.
not sure where I’ll do from here, I guess recheck for vacuum leaks maybe?
Edward
the new sensor does seem to have helped, it’* not quite as lean as it used to be. LTFT are usually between 10-15%, lowest when accelerating from a stop, sometimes 7-8%, and highest when maintaining about 35-45 mph, at about 15%. At idle about 11-12%or so. The biggest difference is when I start coasting it no longer jumps 5-15%, now only maybe 2%. Everything else on the live data looks fine except the downstream o2 sensors are both still reading 99.2%.
not sure where I’ll do from here, I guess recheck for vacuum leaks maybe?
Edward
Senior Member
True Car Nut
Joined: Feb 2015
Posts: 6,849
Likes: 1,014
From: Earth
What are the before/after readings, complete with negative signs where applicable?
Thread Starter
Member
Posts like a V-Tak
Joined: Nov 2025
Posts: 34
Likes: 32
I think the intake manifold pressure is actually ok. I’ve been trying to find normal readings for all these data points and I found the wrong thing. The IMP has stayed the same throughout.
I’ll resmoke for vacuum leaks, in a day or two when I get a chance.
is there anything I can do to check the pvc system? The intake manifold was kinda oily when I removed it for the gaskets. But as far as I can tell it’* a non serviceable kind.
thank you,
Edward
I’ll resmoke for vacuum leaks, in a day or two when I get a chance.
is there anything I can do to check the pvc system? The intake manifold was kinda oily when I removed it for the gaskets. But as far as I can tell it’* a non serviceable kind.
thank you,
Edward
Thread Starter
Member
Posts like a V-Tak
Joined: Nov 2025
Posts: 34
Likes: 32
It loses a little oil, doesn’t smoke but I may add a quart or so between oil changes.
the pcv valve unfortunately isn’t the serviceable variety, but perhaps one advantage of a van is that I can actually get my face in there and blow and suck it without taking it out. Air passed easily both ways. Which I’m pretty sure means that valve isn’t doing its job, right?
thanks
the pcv valve unfortunately isn’t the serviceable variety, but perhaps one advantage of a van is that I can actually get my face in there and blow and suck it without taking it out. Air passed easily both ways. Which I’m pretty sure means that valve isn’t doing its job, right?
thanks
Senior Member
True Car Nut
Joined: Feb 2015
Posts: 6,849
Likes: 1,014
From: Earth
It loses a little oil, doesn’t smoke but I may add a quart or so between oil changes.
the pcv valve unfortunately isn’t the serviceable variety, but perhaps one advantage of a van is that I can actually get my face in there and blow and suck it without taking it out. Air passed easily both ways. Which I’m pretty sure means that valve isn’t doing its job, right?
thanks
the pcv valve unfortunately isn’t the serviceable variety, but perhaps one advantage of a van is that I can actually get my face in there and blow and suck it without taking it out. Air passed easily both ways. Which I’m pretty sure means that valve isn’t doing its job, right?
thanks
Should only go one way.
Thread
Thread Starter
Forum
Replies
Last Post
