Codes - GM Forum - Buick, Cadillac, Chev, Olds, GMC & Pontiac chat


Cadillac When starting new posts, please specify YEAR, MAKE, MODEL, ENGINE type, and whatever modifications you have made.

Reply
 
 
 
Thread Tools Search this Thread
Old 02-26-2016, 03:48 PM   #1
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Apr 2013
Posts: 59
Thanked 0 Times in 0 Posts
Wt4Go is on a distinguished road
Default Codes

2001 DeVille is showing codes: IRC 1064 and PCM 3085. The car sometimes dies when idling or coming to a stop.
The car has 17000 miles on it now and I am looking for your advice on how to keep it running.
Jim
Wt4Go is offline   Reply With Quote
Old 02-29-2016, 04:59 PM   #2
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Apr 2013
Posts: 59
Thanked 0 Times in 0 Posts
Wt4Go is on a distinguished road
Default

Does anyone know where I can find out what the codes mean?
Jim
Wt4Go is offline   Reply With Quote
Old 02-29-2016, 06:26 PM   #3
Senior Member

True Car Nut
 
WilliamE's Avatar
 
Join Date: Jun 2011
Location: VA
Posts: 3,087
Thanked 418 Times in 376 Posts
WilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond repute
Default

Found the info from a manual on another site.

U1064 - Loss of Communications with DIM

DTC U1064 Loss of Communications with DIM
Refer to Data Link Connector (DLC) Schematics

Circuit Description
The class 2 serial data line communicates information between modules. Each module connected to the serial data line is assigned a recognition code, or address. This code is used in order to identify which modules are communicating. Modules communicate with each other by periodically sending state of health (SOH) messages. When the ignition switch is in RUN, each module communicating on the serial data line sends a SOH message every 2 seconds. This ensures that the system is operating properly. When the dash integration module (DIM) stops communicating on the class 2 serial data line, the SOH that is normally sent on the serial data line every 2 seconds disappears. The module, which expects to receive that message, detects the absence of the message. The module in turn sets DTC U1064 associated with the loss of SOH of the DIM.

Conditions for Setting the DTC
The module does not receive a state of health (SOH) message back from the DIM. The module retries the request 3 times, and then sets DTC U1064.
This DTC only sets if U1300 or U1301 is not current.
Action Taken When the DTC Sets
DTC U1064 is stored in the module.
The module uses the default values for the initialization data.
This DTC does not cause driver warning message to appear.

Conditions for Clearing the DTC
This DTC clears (status changes from current to history) under any of the following conditions:
The module detects a state of health message from the DIM.
At each ignition cycle.
A history DTC clears after 50 consecutive ignition cycles if the conditions for setting the DTC are no longer present.
Current and history DTCs may be cleared using a scan tool.
Diagnostic Aids
DTC U1064 does not normally represent a failure within the module.
When loss of class 2 serial data communication DTCs (DTCs with the letter U as the prefix) are stored as history DTCs, know all possible serial data DTCs set in each module before diagnosing the serial data line.
If U1064 is stored in the module memory, inspect for the same DTC stored in other modules capable of storing this DTC.
If the DTC is a history DTC, the problem may be intermittent.
Test Description
The numbers below refer to the step numbers on the diagnostic table:

U1064 is the result of loss of communication with the dash integration module (DIM). Note that other modules on the class 2 serial data line may also set U1064 if the DIM is not communicating with the serial data line.

Clear all DTCs after the repair procedure is complete.

Step
Action
Value(*)
Yes
No

1
Did you perform the Data Link Communications Diagnostic System Check?
--
Go to Step 2
Go to Diagnostic System Check - Data Link Communications

2
Use a scan tool in order to attempt the establish communication with the dash integration module (DIM).

Does the scan tool communicate with the DIM?
--
Go to Step 3
Go to Diagnostic System Check - Body Control System in Body Control System.

3
Inspect and repair the class 2 serial data line CKT 1807 (PPL) for intermittent connections. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.

Is the repair complete?
--
Go to Step 4
--

4
Turn off the ignition switch.
Reconnect or install any connectors or components that were disconnected or removed.
Turn on the ignition switch.
Clear any DTCs.
Is the repair complete?

-------------------------------------

Cannot find anything on the other code, maybe somebody else can be of help.
WilliamE is offline   Reply With Quote
Old 03-01-2016, 09:23 AM   #4
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Apr 2013
Posts: 59
Thanked 0 Times in 0 Posts
Wt4Go is on a distinguished road
Default

William E, thank you very much for the information.
Jim
Wt4Go is offline   Reply With Quote
Old 03-01-2016, 05:24 PM   #5
Senior Member

True Car Nut
 
WilliamE's Avatar
 
Join Date: Jun 2011
Location: VA
Posts: 3,087
Thanked 418 Times in 376 Posts
WilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond reputeWilliamE has a reputation beyond repute
Default

Very welcome, again I am sorry I could not find info on the PCM code, hopefully somebody else will post some info on that sooon.
WilliamE is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
How to pull ABS codes and what oil for supercharger case??? RyanSSEi 1992-1999 1 12-16-2002 03:06 PM
electronic climate control trouble codes Fordolet General GM Chat 8 11-21-2002 01:19 AM
95 SSEi codes - how to get em? DanCulkin 1992-1999 4 10-12-2002 01:05 AM
engine codes G2SSEi95 1992-1999 2 10-10-2002 10:04 PM
Clearing Climate Control Codes and Computer - Anyone ?? CDecker 1992-1999 3 07-12-2002 09:53 AM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 12:14 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.