Turn signal. - GM Forum - Buick, Cadillac, Chev, Olds, GMC & Pontiac chat


1992-1999 Series I L27 (1992-1994 SE,SLE, SSE) & Series II L36 (1995-1999 SE, SSE, SLE) and common problems for the Series I and II L67 (all supercharged models 92-99) Including Olds 88's, Olds LSS's and Buick Lesabres Please use General Chat for non-mechanical issues, and Performance and Brainstorming for improvements.

Reply
 
 
 
Thread Tools Search this Thread
Old 10-26-2004, 10:20 PM   #1
Junior Member
Thread Starter
 
Join Date: Oct 2004
Location: Southwest
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
tigershark is on a distinguished road
Default Turn signal.

Got a 94 Bonneville sse and its all nice and everything, gots leather and everything is nice pine fresh, with the exception of the turn signal, the other day, i was driving and when I went to get to put on the turn signal the entire thing fell off, the stick was just hanging from the wires, now I hear I have to take the column off.. is that true? are there any kind of tips you guys can give me so I can get this thing going again. thanks.
tigershark is offline   Reply With Quote
Old 10-27-2004, 09:59 AM   #2
Senior Member
Posts like a 4 Banger
 
Join Date: Dec 2003
Location: Edison, NJ
Posts: 123
Thanks: 0
Thanked 0 Times in 0 Posts
kaps is on a distinguished road
Default

should just pop right back in, unless the housing broke or something else happened. Try that first, or take a peek inside with a flash light and see if you see anything broken
kaps is offline   Reply With Quote
Old 10-27-2004, 10:11 AM   #3
Senior Member
True Car Nut
 
Join Date: Feb 2004
Location: Western MA
Posts: 2,708
Thanks: 0
Thanked 1 Time in 1 Post
randman1 is on a distinguished road
Default

Disable the Supplemental Inflatable Restraint (SIR) system as described in MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING prior to working on or near the steering column.

Remove steering wheel as described in STEERING WHEEL.
Using lock plate compressor tool No. J 23653-C or equivalent, push down shaft lock and remove shaft lock retaining ring.
Remove shaft lock, turn signal cancelling cam assembly, upper bearing spring, upper bearing inner race seat and inner race.
Set turn signal to RIGHT TURN position, then remove multi-function lever and hazard **** assembly, Fig. 16.
Remove signal switch arm retaining screw and switch arm.
Remove turn signal switch attaching screws, then signal switch as follows:
Disconnect turn signal switch connector from bulkhead connector and wire harness strap, Fig. 17.
Disconnect E & C module connector from signal switch harness.
Remove wiring protector, then nut holding ground wire to stud.
Gently pull wire harness through column.
Reverse procedure to install.
Rearm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

I don't see "remove the column" but it does seem to require a lot of digging. If you find that it is broken and needs to be replaced, I have a spare column and can take some pics if necessary to help you through the procedure. Send my your email via PM so I can include some more information that might help.
randman1 is offline   Reply With Quote
Old 10-27-2004, 11:26 AM   #4
Senior Member
Posts like a Turbo
 
Join Date: Feb 2003
Location: Detroit
Posts: 302
Thanks: 0
Thanked 0 Times in 0 Posts
94bonnyV is on a distinguished road
Default

have a similar problem you should be able to re insert the lever, but it may require some rotating of the different pieces to get it ti sit all the way in. Mine is quite broken and if i grab it wrong it will pop out... you'll get the hang of fixing it
94bonnyV is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
turn signal arm is loose and high beams wont turn on!! artofwar215 1992-1999 2 03-16-2007 09:38 PM
Turn signal problem rhamby 1992-1999 7 06-27-2003 02:53 PM
DIC reporting Turn Signal Light Out Merlin 91/97 1987-1991 4 06-02-2003 02:14 PM
Turn signal alert pontiacfan1978 General GM Chat 10 10-24-2002 04:08 AM
How Do I Create My Scanner Light Turn Signal????? DJGOODYB31682 1992-1999 4 10-22-2002 12:47 AM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 02:36 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.