Console Gear Indicator Lights
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2009
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Console Gear Indicator Lights
Hey guys, my console lights for PRNOD21 work just fine. It is the small round indicators beside each letter that show you what gear you are in that do not illuminate. I got the console partly apart, (could not get the shifter handle off) and saw the light bulb for the letters was on. Then I saw a wire going to each indicator but they do not work. Checked the fuses and all. What controls these lights? Where could I find that info out? I did a google search and it led me to a thread from in here but would not allow me access to that info in the electrical section. Thanks
Also how does the shifter handle come off?
Also how does the shifter handle come off?
Last edited by novapwr; 11-06-2009 at 06:59 PM. Reason: left out something
#2
I don't know, but I'm going to dig into it this weekend I hope. It used to work so I know it'* supposed to. Mine'* a 1998 SE.
Last edited by risteff; 04-13-2010 at 02:48 AM. Reason: left out year
#3
DINOSAURUS BOOSTUS
Expert Gearhead
I forget which style your car has. Some had a single bulb that lit the whole thing and the other style had one bulb further down that lit through what looked like fiber optics to each gear. Kinda sounds like you might have the latter.
Either way, there is a bulb. Sorry I don't think I have any pictures at the moment.
Either way, there is a bulb. Sorry I don't think I have any pictures at the moment.
#4
Senior Member
Posts like a Turbo
Join Date: Jan 2010
Location: Tonawanda NY
Posts: 387
Likes: 0
Received 0 Likes
on
0 Posts
#5
Yep. C clip in the front of the shifter handle. Pulled it out, removed the torx from under the ashtray & lifted the consol. unscrewed, removed, and opened a plastic rectangular box from under the shift indicator and found a circuit board thingy with light bulbs on it. These look to be soldered on. Anyone know for sure where I sould go from here? I'll have to take it apart agian as I forgot to get pics the first time. There is a 4 wire harness (plug) that goes to it. Anyone know what wire is for what? I'm guessing B+, GRND, and perhaps the other two go the the door locks. (doors lock when you take it out of park) Thanks for any input.
#6
Senior Member
Posts like a Turbo
Join Date: Dec 2009
Location: Kitchener On.
Posts: 348
Likes: 0
Received 0 Likes
on
0 Posts
I think you are right and that circuit board is the tran. position decoder module.
grey wire B+, black & white ground if you have power there than i would say bad module unless you can chec each individual light circuit
grey wire B+, black & white ground if you have power there than i would say bad module unless you can chec each individual light circuit
#7
Thanks. I'm getting ready to take it apart again in an hour or so. I'll be gettin' pics this time. I'll check the voltage although I believe it'* good. The Park dot lights up when I first start the car & then goes out right away. If I start it quickly & shift out of park, the dot stays lit at park & doesn't move. I'll give an update soon.
#8
Oh man...I got it apart again & I have no freakin' idea what makes this thing work! I took some pics (found out I'm not a photographer.) Wires are all good & working. What makes the it know where the shifter is? Btw, does anyone know where I can get a replacement bulb? The LEDs work, I need the other one. # is CM 8-A126. I'm not finding it anywhere.
Last edited by risteff; 04-25-2010 at 02:29 AM.
Thread
Thread Starter
Forum
Replies
Last Post