Torque wrench
#1
Senior Member
True Car Nut
Thread Starter
Join Date: Jun 2003
Location: Purgatory
Posts: 6,313
Likes: 0
Received 0 Likes
on
0 Posts
Torque wrench
I have a Snap-on torque wrench that I had not used in a while. I caught up with a Snap-on truck yesterday and had it checked. He must have been in a good mood, because he did not charge me for having it done. I later tested my cheapy (used for wheels and lives in the trunk from time to time) against the snap on and found it almost 10lbs off
I now have it dialed in at 110 ft/lbs but actually it torques to 100.
btw the snap on was only out by a half pound and the salesman has every thing to calibrate it.
I now have it dialed in at 110 ft/lbs but actually it torques to 100.
btw the snap on was only out by a half pound and the salesman has every thing to calibrate it.
#2
Senior Member
True Car Nut
Join Date: Sep 2004
Location: Farmington, Minnesota =MWBF '05 SURVIVOR= =CEBF '06 SURVIVOR= =August '06 COTM=
Posts: 9,130
Likes: 0
Received 0 Likes
on
0 Posts
Nice.....But don't leave them set when you're not using them. Always back them back down to 0. Other wise you ruin them.
#3
Senior Member
True Car Nut
Thread Starter
Join Date: Jun 2003
Location: Purgatory
Posts: 6,313
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by LakevilleSSEi
Nice.....But don't leave them set when you're not using them. Always back them back down to 0. Other wise you ruin them.
#4
Senior Member
True Car Nut
Join Date: Sep 2004
Location: Farmington, Minnesota =MWBF '05 SURVIVOR= =CEBF '06 SURVIVOR= =August '06 COTM=
Posts: 9,130
Likes: 0
Received 0 Likes
on
0 Posts
Ya there'* a spring in there that holds tension and when you set the amount of tq. you want, the spring compresses, and if you don't release the setting all the way back done to 0 that spring starts to stay compressed.
#5
Senior Member
Posts like a Turbo
Join Date: Jan 2005
Location: Hanoverpark/palatine IL, wrenchin' and cursin'
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
yeah ya have to treat your Tq wrenche right...always reset to 0 i do it even if i am going to lunch for 30 minutes...
i just bought this:
TECHWRENCH® FEATURES
TECHMEMORY™ Electronic Torque Wrenches include TORQLOGT™, a downloading software on CD for IBM PC’* and a 6 ft. RS232 serial cable. Two Microsoft® Excel® templates are also on the CD for customer convenience. The DOWNLOAD template provides basic statistical analysis of dumped readings. The DATE/TIME template adds a date and time stamp to each reading while the wrench is attached to the PC. Templates can be customized to suit specific user needs.
http://buy1.snapon.com/catalog/item....re&dir=catalog
this round out my collection..
i have 2 dial type (gold cert) one a 1/4 inch and the other 3/8 drive (i set up more than a few rearends...damn bearing preload )
along with a Buffalo 1/4 inch 750 inch pounder (clicker)from my gramps that i had tested and it was only 4% off not bad for a well maintained 20 year old Tq wrench...
soo now i have a 50-250 ftlb 1/2 inch drive....
now i just need to buy the MAC digital tq angle meter get rid of my damn dial one that dont do **** when tqing ls1 heads in an Fbody or otherwise...
TM3559
Digital Torque Angle Meter
Unique piezo gyro technology. Angle
meter clips onto standard socket
extension or similar drive tool.
Measure angle 0-199° with 1% CW
accuracy. Simple arrow key operation
to set desired angle beep and
flash feedback. Battery power provides
12 hours use (CR2035). Auto
power off.
i just bought this:
TECHWRENCH® FEATURES
TECHMEMORY™ Electronic Torque Wrenches include TORQLOGT™, a downloading software on CD for IBM PC’* and a 6 ft. RS232 serial cable. Two Microsoft® Excel® templates are also on the CD for customer convenience. The DOWNLOAD template provides basic statistical analysis of dumped readings. The DATE/TIME template adds a date and time stamp to each reading while the wrench is attached to the PC. Templates can be customized to suit specific user needs.
http://buy1.snapon.com/catalog/item....re&dir=catalog
this round out my collection..
i have 2 dial type (gold cert) one a 1/4 inch and the other 3/8 drive (i set up more than a few rearends...damn bearing preload )
along with a Buffalo 1/4 inch 750 inch pounder (clicker)from my gramps that i had tested and it was only 4% off not bad for a well maintained 20 year old Tq wrench...
soo now i have a 50-250 ftlb 1/2 inch drive....
now i just need to buy the MAC digital tq angle meter get rid of my damn dial one that dont do **** when tqing ls1 heads in an Fbody or otherwise...
TM3559
Digital Torque Angle Meter
Unique piezo gyro technology. Angle
meter clips onto standard socket
extension or similar drive tool.
Measure angle 0-199° with 1% CW
accuracy. Simple arrow key operation
to set desired angle beep and
flash feedback. Battery power provides
12 hours use (CR2035). Auto
power off.
Thread
Thread Starter
Forum
Replies
Last Post