Keyless Entry
#1
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: May 2006
Location: Toronto, Ontario
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Keyless Entry
Hey everyone,
Im new too the forums. I just bought a 1999 Bonneville SSEI.
My question is, my keyless entry doesnt work. I changed the battery as well as following the steps on the tech info page listed below:
"1. Turn the ignition switch OFF.
Use a fused jumper wire in order to jumper the DLC terminal 8 (BLK/WHT) to terminal 4 (BLK).
2. Close all of the doors.
3. Turn the ignition switch ON. The doors will cycle to lock.
4. Press and hold the LOCK button and the UNLOCK button on one transmitter. After a 30 second delay the doors will lock and unlock.
Important
Do not turn the ignition OFF or the first transmitter will become inoperative.
5. In order to program extra transmitters, repeat step 4.
6. Disconnect the fused jumper wire from the DLC."
I did that, instead of using a 3 amp fused wire, because I dont even know what that is, I used a paper clip cuz I was told it was the same idea. Would this be why it didnt work? If so, where can I get a 3 amp fused wire? And is there anything I could have done wrong?
Im new too the forums. I just bought a 1999 Bonneville SSEI.
My question is, my keyless entry doesnt work. I changed the battery as well as following the steps on the tech info page listed below:
"1. Turn the ignition switch OFF.
Use a fused jumper wire in order to jumper the DLC terminal 8 (BLK/WHT) to terminal 4 (BLK).
2. Close all of the doors.
3. Turn the ignition switch ON. The doors will cycle to lock.
4. Press and hold the LOCK button and the UNLOCK button on one transmitter. After a 30 second delay the doors will lock and unlock.
Important
Do not turn the ignition OFF or the first transmitter will become inoperative.
5. In order to program extra transmitters, repeat step 4.
6. Disconnect the fused jumper wire from the DLC."
I did that, instead of using a 3 amp fused wire, because I dont even know what that is, I used a paper clip cuz I was told it was the same idea. Would this be why it didnt work? If so, where can I get a 3 amp fused wire? And is there anything I could have done wrong?
#2
Senior Member
True Car Nut
Join Date: Oct 2002
Location: Groton, CT _NEBF 05, 06, 07_
Posts: 2,703
Likes: 0
Received 0 Likes
on
0 Posts
Re: Keyless Entry
Originally Posted by mcnutz
I did that, instead of using a 3 amp fused wire, because I dont even know what that is, I used a paper clip cuz I was told it was the same idea. Would this be why it didnt work?
#4
Senior Member
True Car Nut
Join Date: Feb 2006
Location: Somewhere different on the globe every month....
Posts: 2,896
Likes: 0
Received 0 Likes
on
0 Posts
You can do a search for the pics. I will do one for you right now. Welcome to the club. Remember to get a signature to your profile with your car'* info.
#5
any luck on finding the image? I have the same problem and don't wanna f anything up when i go to reprogram the remotes
NM .... found it (and alot more interesting info) while browsing older posts
NM .... found it (and alot more interesting info) while browsing older posts
#7
Junior Member
Posts like a Ricer Type-R
Join Date: Sep 2004
Location: Quad Cities, USA
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Hi.
With all this talk about remote key fobs, it'* made me think.... Ow, my head hurts!
Okay, a bit more seriously. I've lost both my remote keyfobs. I'd like to have them again. They were kinda handy, as I recall. What are the chances any of you have extras you wouldn't mind losing?
Thanks.
With all this talk about remote key fobs, it'* made me think.... Ow, my head hurts!
Okay, a bit more seriously. I've lost both my remote keyfobs. I'd like to have them again. They were kinda handy, as I recall. What are the chances any of you have extras you wouldn't mind losing?
Thanks.
Thread
Thread Starter
Forum
Replies
Last Post
85bonneville
Audio (and aftermarket electronics)
7
02-24-2003 10:22 PM