[Need Assistance With Remote Programming]
Senior Member
True Car Nut
Joined: Feb 2015
Posts: 6,826
Likes: 1,009
From: Earth
The post above was added to another thread when the newest response in that thread was over seven years old. Closed the other thread, moved that post to a new thread, and created a title for the new thread..
Previous thread: https://www.gmforum.com/cadillac-174...amming-304104/
Please do not post in threads that have no entries less than six months old. Please refer to https://www.gmforum.com/introduction...-first-304557/ for more details.
Previous thread: https://www.gmforum.com/cadillac-174...amming-304104/
Please do not post in threads that have no entries less than six months old. Please refer to https://www.gmforum.com/introduction...-first-304557/ for more details.
Last edited by CathedralCub; Jan 9, 2021 at 04:26 PM. Reason: Corrected for clarity
Senior Member
True Car Nut
Joined: Feb 2015
Posts: 6,826
Likes: 1,009
From: Earth
Quoting the procedure originally provided by 2kg4u for easy reference:
There are two step 5'* in the procedures above. To which are you referring?
Where did this remote come from (existing, new, Ebay, junkyard, etc.?) ?
2010 SRX
You have one programmed remote and you want to add another.
1. Vehicle must be off.
2. Place the working remote(*) in the cupholder. Have the new remote with you.
3. Insert the key into the key lock cylinder located on the outside of drivers door.
4.Turn the key to the unlock position five times with in ten seconds.
5. The (DIC) Driver Information Center displays Ready to Learn Electronic key #2, 3, 4 ETC.
6. Place the new remote into the transmitter pocket with the buttons facing the front
of the vehicle. (The transmitter pocket is inside the center console between the
driver and front passanger seats). The storage area will need to be opened and the
storage tray lifted up to access the transmitter pocket.
7. Press the ignition. When the remote is learned the DIC display will show that it is
ready to program the next remote.
8. Remove the remote from the transmitter pocket and press unlock on the remote.
9. To program additional remotes, repeat Steps 6 through 8.
10. When all additional transmitters are programmed, press and hold the ignition for
ten seconds to exit programming mode.
You have no working remotes.
1. The vehicle must be off.
2. Insert the key into the key lock cylinder located on the outside of drivers door.
3.Turn the key to the unlock position five times with in ten seconds.
4. The (DIC) Driver Information Center displays REMOTE LEARN PENDING, PLEASE WAIT.
5. Wait for ten minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN
and then press the ignition.
The DIC displays will again show REMOTE LEARN PENDING, PLEASE WAIT.
6. Repeat Step 5 two additional times. After the third time all previously known remotes will
no longer work with the vehicle. Remaining remotes can be relearned during the next steps.
The DIC display should now show READY FOR REMOTE #1
7. Place the new remote into the transmitter pocket with the buttons facing the front
of the vehicle. (The transmitter pocket is inside the center console between the
driver and front passanger seats). The storage area will need to be opened and the
storage tray lifted up to access the transmitter pocket.
8. Press the ignition. When the remote is learned the DIC display will show that it is
ready to program the next remote.
9. Remove the remote from the transmitter pocket and press unlock on the remote.
10. To program additional remotes, repeat Steps 7 through 9.
11. When all additional transmitters are programmed, press and hold the ignition for
ten seconds to exit programming mode.
You have one programmed remote and you want to add another.
1. Vehicle must be off.
2. Place the working remote(*) in the cupholder. Have the new remote with you.
3. Insert the key into the key lock cylinder located on the outside of drivers door.
4.Turn the key to the unlock position five times with in ten seconds.
5. The (DIC) Driver Information Center displays Ready to Learn Electronic key #2, 3, 4 ETC.
6. Place the new remote into the transmitter pocket with the buttons facing the front
of the vehicle. (The transmitter pocket is inside the center console between the
driver and front passanger seats). The storage area will need to be opened and the
storage tray lifted up to access the transmitter pocket.
7. Press the ignition. When the remote is learned the DIC display will show that it is
ready to program the next remote.
8. Remove the remote from the transmitter pocket and press unlock on the remote.
9. To program additional remotes, repeat Steps 6 through 8.
10. When all additional transmitters are programmed, press and hold the ignition for
ten seconds to exit programming mode.
You have no working remotes.
1. The vehicle must be off.
2. Insert the key into the key lock cylinder located on the outside of drivers door.
3.Turn the key to the unlock position five times with in ten seconds.
4. The (DIC) Driver Information Center displays REMOTE LEARN PENDING, PLEASE WAIT.
5. Wait for ten minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN
and then press the ignition.
The DIC displays will again show REMOTE LEARN PENDING, PLEASE WAIT.
6. Repeat Step 5 two additional times. After the third time all previously known remotes will
no longer work with the vehicle. Remaining remotes can be relearned during the next steps.
The DIC display should now show READY FOR REMOTE #1
7. Place the new remote into the transmitter pocket with the buttons facing the front
of the vehicle. (The transmitter pocket is inside the center console between the
driver and front passanger seats). The storage area will need to be opened and the
storage tray lifted up to access the transmitter pocket.
8. Press the ignition. When the remote is learned the DIC display will show that it is
ready to program the next remote.
9. Remove the remote from the transmitter pocket and press unlock on the remote.
10. To program additional remotes, repeat Steps 7 through 9.
11. When all additional transmitters are programmed, press and hold the ignition for
ten seconds to exit programming mode.
Where did this remote come from (existing, new, Ebay, junkyard, etc.?) ?
Last edited by CathedralCub; Jan 9, 2021 at 04:21 PM. Reason: Removed some unnecessary CRLFs and corrected my grammar.
Thread
Thread Starter
Forum
Replies
Last Post
rel3rd
Performance, Brainstorming & Tuning
14
Oct 2, 2005 01:01 PM