2001 SLE Remote Start Install
Thread Starter
Member
Posts like a V-Tak
Joined: Jun 2005
Posts: 34
Likes: 0
From: Northern Alberta, Canada
2001 SLE Remote Start Install
Good Morning..
I am in the middle of the Ultrta Start remote start install. Does anybody know how the H*** do you gain access to the ignition wires? I pulled the dash cover off, the panel, the radio, climate control and tried to get at the ignition wires.. I unscrewed the two bolts holding the igniton in and there isn't much room to even probe the wires..I can push my hand and touch them but i can't remove the ignition switch..
Does anydoby know if the same ignition wires are coming from the bundle or wires under the dash (there are 2 bundles)..
The main wires that i am looking for are the igniton 1 and 2 and ACC/Heater..
Please help I have been at this for a while now..
I am in the middle of the Ultrta Start remote start install. Does anybody know how the H*** do you gain access to the ignition wires? I pulled the dash cover off, the panel, the radio, climate control and tried to get at the ignition wires.. I unscrewed the two bolts holding the igniton in and there isn't much room to even probe the wires..I can push my hand and touch them but i can't remove the ignition switch..
Does anydoby know if the same ignition wires are coming from the bundle or wires under the dash (there are 2 bundles)..
The main wires that i am looking for are the igniton 1 and 2 and ACC/Heater..
Please help I have been at this for a while now..
Senior Member
True Car Nut
Joined: Feb 2004
Posts: 2,708
Likes: 2
From: Western MA
You went too far right.
Remove the 2-3 7mm screws that attach the hush panel (black panel under the dasah). You already have the dash trim off so now, remove the 4 10mm bolts that hold the trim panel directly under the steering column. They they are... really easy to get at.
Ign 1 is pink, there is no ign 2 and the heater wire is orange. Don't forget to connect the VATS bypass and the Factory Alarm Disarm if you have the factory alarm (RPO code UA6)
Remove the 2-3 7mm screws that attach the hush panel (black panel under the dasah). You already have the dash trim off so now, remove the 4 10mm bolts that hold the trim panel directly under the steering column. They they are... really easy to get at.
Ign 1 is pink, there is no ign 2 and the heater wire is orange. Don't forget to connect the VATS bypass and the Factory Alarm Disarm if you have the factory alarm (RPO code UA6)
Thread Starter
Member
Posts like a V-Tak
Joined: Jun 2005
Posts: 34
Likes: 0
From: Northern Alberta, Canada
Originally Posted by randman1
You went too far right.
Remove the 2-3 7mm screws that attach the hush panel (black panel under the dasah). You already have the dash trim off so now, remove the 4 10mm bolts that hold the trim panel directly under the steering column. They they are... really easy to get at.
Ign 1 is pink, there is no ign 2 and the heater wire is orange. Don't forget to connect the VATS bypass and the Factory Alarm Disarm if you have the factory alarm (RPO code UA6)
Remove the 2-3 7mm screws that attach the hush panel (black panel under the dasah). You already have the dash trim off so now, remove the 4 10mm bolts that hold the trim panel directly under the steering column. They they are... really easy to get at.
Ign 1 is pink, there is no ign 2 and the heater wire is orange. Don't forget to connect the VATS bypass and the Factory Alarm Disarm if you have the factory alarm (RPO code UA6)
Thread
Thread Starter
Forum
Replies
Last Post
Whostens
Audio (and aftermarket electronics)
9
Jan 26, 2008 10:08 AM
Glasuan
Audio (and aftermarket electronics)
9
Oct 22, 2004 11:19 AM
randy
Audio (and aftermarket electronics)
18
Nov 3, 2003 02:19 PM