Stalling while driving
#1
Senior Member
True Car Nut
Thread Starter
Join Date: Jan 2005
Location: Montevideo, MN MWBF '05, '06, '07 WCBF '06 '07 survivor
Posts: 3,882
Likes: 0
Received 0 Likes
on
0 Posts
Stalling while driving
On the SSEi. I have gotten 2 P0336'* in like the last 2 weeks. These happened while driving down the road, noticed nothing unusual with the drive.
Before all this I would get like a power loss (maybe 1/2 sec) intermittantly(maybe once a week). Felt like the cruise was letting go and then catching itself. That'* what I chalked it up to.(no codes)
Now after the 2 336'*, I am getting actual stalling while the engine is running. This has happened idleing, and while driving down the highway. I slip the car into neutral, start the car while rolling, and am back on my way. I loose about 10 mph during this process. But it hasn't thrown a code while doing this.
Suggestions? ( I was going to start with crank sensor)
I also lost my right tip (stock) today. When I was replacing my elc I noticed my muffler and tip joints were getting bad. Although the muffler doesn't sound bad or rattle, the interior weld spots are rusting through. Starting the process of looking for new muffler and tips. (Don't want loud, but more then stock) There is no where around here to go and look at whats available. I'll have to make a trip to the cites. Anyone have suggestions for shops there?
Before all this I would get like a power loss (maybe 1/2 sec) intermittantly(maybe once a week). Felt like the cruise was letting go and then catching itself. That'* what I chalked it up to.(no codes)
Now after the 2 336'*, I am getting actual stalling while the engine is running. This has happened idleing, and while driving down the highway. I slip the car into neutral, start the car while rolling, and am back on my way. I loose about 10 mph during this process. But it hasn't thrown a code while doing this.
Suggestions? ( I was going to start with crank sensor)
I also lost my right tip (stock) today. When I was replacing my elc I noticed my muffler and tip joints were getting bad. Although the muffler doesn't sound bad or rattle, the interior weld spots are rusting through. Starting the process of looking for new muffler and tips. (Don't want loud, but more then stock) There is no where around here to go and look at whats available. I'll have to make a trip to the cites. Anyone have suggestions for shops there?
#2
Senior Member
Posts like a Turbo
Join Date: Jul 2004
Posts: 226
Likes: 0
Received 0 Likes
on
0 Posts
I'* the crank sensor. Happened on my Taurus SHO. It would just cut out any time it wanted to and come back any time it wanted to. The sensor is on its way out. Replace it.
#3
Senior Member
True Car Nut
Join Date: Sep 2004
Location: Farmington, Minnesota =MWBF '05 SURVIVOR= =CEBF '06 SURVIVOR= =August '06 COTM=
Posts: 9,130
Likes: 0
Received 0 Likes
on
0 Posts
I think I have my stock tips if you want them........
I'd shop on Ebay and check out magnaflow, flowmasters, and tips there.
Jason and I maybe getting together tommorow.....If you wanna make a trip out to repair that crank sensor
I'd shop on Ebay and check out magnaflow, flowmasters, and tips there.
Jason and I maybe getting together tommorow.....If you wanna make a trip out to repair that crank sensor
#4
Junior Member
Posts like a Ricer Type-R
Join Date: Jun 2005
Location: SE Michigan
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
I have similar problems but my code is 316. Going to change the ignition control module today and if that does not help then try the crank trigger sensor. Good luck with yours.
Grumpy
Grumpy
Thread
Thread Starter
Forum
Replies
Last Post