Supercharger Install Steps
#1
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Jul 2004
Location: Bolingbrook, IL Location: Clarkston, MI
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
Supercharger Install Steps
Supercharger is ready to be put back together and installed again! Just a few ?'* before I begin.
What type of grease should I use to pack the 2 needle bearings in the case?
What steps and torque (lbs.) to mount the */C to the lower intake manifold?
What type of grease should I use to pack the 2 needle bearings in the case?
What steps and torque (lbs.) to mount the */C to the lower intake manifold?
#2
Junior Member
Posts like a Ricer Type-R
Ummmm....where did you get the needle bearings? Didn't they come pre-packed? I hopee so, because the grease is $50 an ounce or so.
Torque specs are in my sig pic. On my Bonneville page, click on "Click Here" to go to my thumbnail page. a few pages in you'll see some scanned pages that I got from Magnusson a couple years ago. They have the torque specs for the 'charger. Techinfo has the specs for mounting it to the LIM.
Torque specs are in my sig pic. On my Bonneville page, click on "Click Here" to go to my thumbnail page. a few pages in you'll see some scanned pages that I got from Magnusson a couple years ago. They have the torque specs for the 'charger. Techinfo has the specs for mounting it to the LIM.
#3
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Jul 2004
Location: Bolingbrook, IL Location: Clarkston, MI
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
I checked in techinfo before and couldn't find them. . . . . . . . . Checked again and found 'em (note to self: double check)
As some of you guys know 2 days after IDD my fuel pump took a dump and I saw this down time as a great time to take off the */C and clean it.
As for the needle bearings they are stock and still good. The bearings still have grease in 'em but I wanted to pack them right if I was going to put the */C back together.
So I guess the ? is where do I get some from? I know Intense sells it and I know if I call up ZZP they will get me some. But I was really hoping to get it locally so I could get the car back together. Does GM even have */C grease? If so PN?
edit: too late and too many beers to type
As some of you guys know 2 days after IDD my fuel pump took a dump and I saw this down time as a great time to take off the */C and clean it.
As for the needle bearings they are stock and still good. The bearings still have grease in 'em but I wanted to pack them right if I was going to put the */C back together.
So I guess the ? is where do I get some from? I know Intense sells it and I know if I call up ZZP they will get me some. But I was really hoping to get it locally so I could get the car back together. Does GM even have */C grease? If so PN?
edit: too late and too many beers to type
#4
Junior Member
Posts like a Ricer Type-R
GM does NOT sell the grease, as they don't service SC'*, except to replace either the whole thing, or just the nose drive.
It'* actually some super-special magic amazing grease developed by Eaton for this application. I can't remember the names, but there'* two types that can be used in this application. Both are VERY expensive.
It'* actually some super-special magic amazing grease developed by Eaton for this application. I can't remember the names, but there'* two types that can be used in this application. Both are VERY expensive.
#5
!! UNCONFIRMED EMAIL !!
Posts like a Northstar
Join Date: Nov 2004
Posts: 584
Likes: 0
Received 0 Likes
on
0 Posts
#6
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Jul 2004
Location: Bolingbrook, IL Location: Clarkston, MI
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
Got some from a buddy up in Grand Rapids!
*/C in now on and running. . . . . . . . . . .tho A/C Compressor bearings are shot and is getting really loud. . . . . . . . . .Grrrrrr
*/C in now on and running. . . . . . . . . . .tho A/C Compressor bearings are shot and is getting really loud. . . . . . . . . .Grrrrrr
Thread
Thread Starter
Forum
Replies
Last Post
harofreak00
Detailing & Appearance
6
06-05-2004 06:15 PM
Damemorder
Performance, Brainstorming & Tuning
7
03-23-2004 07:11 PM