problems with my L67 - Page 6 - GM Forum - Buick, Cadillac, Chev, Olds, GMC & Pontiac chat


Performance, Brainstorming & Tuning Talk about modifications, or anything else associated with performance enhancements. Have a new idea for performance/reliability? Post it here. No idea is stupid! (please use Detailing and Appearance for cosmetic ideas)

Reply
 
 
 
Thread Tools Search this Thread
Old 04-08-2007, 07:25 PM   #51
Junior Member
Posts like a Ricer Type-R
 
Join Date: Aug 2002
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
willwren is on a distinguished road
Default

Quote:
fuel pump, axles, complete engine and transmissioin, pcm was reprogrammed from INTENSE-RACING, for installation i had to buy a L36 to L67 swap kit from ZZPerformance.
What did the swap kit include?
willwren is offline   Reply With Quote
Old 04-08-2007, 08:18 PM   #52
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Jul 2006
Location: killeen texas
Posts: 49
Thanks: 0
Thanked 0 Times in 0 Posts
kyrt320 is on a distinguished road
Default

it had two wires to add onto the L36 harness it came with a Supercharger bypass connector and MAP adapter wire. and sorry about the typo. i checked the trottle position sensor. and the wires was hardwired in. as for what the PCM is trying to tell me???? i have no idea. i have no check engine light or service engine light. as far as i can tell the PCM is trying to tell me that everything is fine. but when i start the car it starts up like normal and as soon as it tries to go back to idle it dies out. i was told that it was the fuel pump. i just had it towed from GeorgeTown, TX so i have my car back in my drive way. i have also unplugge almost every connector i can reach and checked to make sure that it was good. and from what i can tell everything is like it should be. so i am drawing a blank here. any ideas or any info needed?
kyrt320 is offline   Reply With Quote
Old 04-08-2007, 08:28 PM   #53
Junior Member
Posts like a Ricer Type-R
 
Join Date: Aug 2002
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
willwren is on a distinguished road
Default

Spark and fuel make fire. You need to verify both. We need to know your fuel pressure at the rail, and we need to know if you're getting spark at the front three plugs during cranking.

Shopping for a scantool yet?
willwren is offline   Reply With Quote
Old 04-08-2007, 08:31 PM   #54
Senior Member
Posts like a Supercharger
 
Join Date: May 2003
Location: Columbus, OH
Posts: 163
Thanks: 0
Thanked 0 Times in 0 Posts
13secGTP is on a distinguished road
Default

The ZZP swap kit includes an adapter plug to run the 2bar GM MAP sensor, and plug with wiring for the boost solenoid.

And as for the car not running:

Are you setting any security codes? Or lights? Sometimes you won't get one at all.
If so there are a couple things to try
1- do a security relearn
2- disable the security in the PCM (this only tells the PCM not to look for the BCM)

The issue seems like the fuel pump or FP resisitor everytime it happens

This is most common on top swapped vehicles, but once and a while happens on complete swaps.

And to the rest of you that think just because the PCM was reprogramed for an L67, doesn't mean it will read the soleniod. It doesn't matter if it programmed by YOU, me, Intense, ZZP, DHP, ect....It still started its life as an L36 PCM-Make sense now? What he needs is to transfer the same file from his current PCM to an L67 PCM..Or vin changing..
Now if somewhere he did start with an L67 PCM -please show me in this thread, I had to have missed that.
13secGTP is offline   Reply With Quote
Old 04-08-2007, 08:44 PM   #55
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Jul 2006
Location: killeen texas
Posts: 49
Thanks: 0
Thanked 0 Times in 0 Posts
kyrt320 is on a distinguished road
Default

yes at first we used a L67 PCM but when we put it in it did not even start (no injector pulse) we send the PCM back to intense they sent us another one and it still didn't work. but when we plugged in the original PCM for my car it ran. but it ran horribly. so i sent my PCM back to intense and the programmed in the neccessary codes into the PCM.

Quote:
13secGTP Posted: Sun Apr 08, 2007 6:31 pm Post subject:

--------------------------------------------------------------------------------

The ZZP swap kit includes an adapter plug to run the 2bar GM MAP sensor, and plug with wiring for the boost solenoid.

And as for the car not running:

Are you setting any security codes? Or lights? Sometimes you won't get one at all.
If so there are a couple things to try
1- do a security relearn
2- disable the security in the PCM (this only tells the PCM not to look for the BCM)

how do i delete the security codes from the PCM. i know i'm getting fuel. i checked the fuel and i am getting fuel. how do i check for spark (hold on if i'm not getting spark, wouldn't the car not start in the first place even though it is starting just won't stay running?)
kyrt320 is offline   Reply With Quote
Old 04-08-2007, 08:57 PM   #56
Senior Member
Posts like a Supercharger
 
Join Date: May 2003
Location: Columbus, OH
Posts: 163
Thanks: 0
Thanked 0 Times in 0 Posts
13secGTP is on a distinguished road
Default

I don't have the learn procedure in front of me for anything. They are on my other PC. However I'm sure they are on this site somewhere, everything Bonneville is-lol.

You really need to get a good scanner.

LS1m
PowrTunr
HPtuner

The HPT and PT will give you the ability to reprog. the PCM yourself. A little costly and you need a laptop, but for what you have going either will end up saving you TONS of cash in the long run.

To disable the security with the PT.
Open your .bin file
click-diagnostics
click-security
click-disable_flash_securty
change default to 255
exit-accept changes

No IPW with the L67 PCM? I've only seen that 1 other time, and it was on an 00 Monte. Try another L67 PCM, and have your .bin file uploaded to it. get one from a GP , the GP PCMs seem to be a little more forgiving. Also try running it with a stock unmolested L67 PCM. then disable security.

I hate this my mind works faster than I do on things like this. There are a lot more possibilties. But what I'm posting are the most common problems.
13secGTP is offline   Reply With Quote
Old 04-08-2007, 11:23 PM   #57
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Jul 2006
Location: killeen texas
Posts: 49
Thanks: 0
Thanked 0 Times in 0 Posts
kyrt320 is on a distinguished road
Default

i know the relearn procedure. so try that? but this is what confuses me. when i tried installing the SSEi PCM and the security procedure was required the car wouldn't even try to turn over. so i need to do the security relearn again because my PCM is thinking the car is being stolen? but why did the car initially die while i was driving (i'm sure i said that) well it didn't die it seemed like it went to idle while i was dirving and no matter how muh i hit the gas the RPM would not go up. when i stopped the car died out and did not start back up normally since then. if i did not mention this before i apologize but it happened at 3:00 this morning so i'm running low on gas myself right now.
kyrt320 is offline   Reply With Quote
Old 04-09-2007, 10:05 AM   #58
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Jul 2006
Location: killeen texas
Posts: 49
Thanks: 0
Thanked 0 Times in 0 Posts
kyrt320 is on a distinguished road
Default

Quote:
Originally Posted by 13secGTP
I don't have the learn procedure in front of me for anything. They are on my other PC. However I'm sure they are on this site somewhere, everything Bonneville is-lol.

You really need to get a good scanner.

LS1m
PowrTunr
HPtuner

The HPT and PT will give you the ability to reprog. the PCM yourself. A little costly and you need a laptop, but for what you have going either will end up saving you TONS of cash in the long run.

To disable the security with the PT.
Open your .bin file
click-diagnostics
click-security
click-disable_flash_securty
change default to 255
exit-accept changes

No IPW with the L67 PCM? I've only seen that 1 other time, and it was on an 00 Monte. Try another L67 PCM, and have your .bin file uploaded to it. get one from a GP , the GP PCMs seem to be a little more forgiving. Also try running it with a stock unmolested L67 PCM. then disable security.

I hate this my mind works faster than I do on things like this. There are a lot more possibilties. But what I'm posting are the most common problems.
can i use the LS1M to have the same effect as the HPT or PT?
kyrt320 is offline   Reply With Quote
Old 04-09-2007, 10:24 AM   #59
DINOSAURUS BOOSTUS

Expert Gearhead
 
BillBoost37's Avatar
 
Join Date: Mar 2005
Location: Enfield, CT
Posts: 41,391
Thanks: 0
Thanked 0 Times in 0 Posts
BillBoost37 is a glorious beacon of lightBillBoost37 is a glorious beacon of lightBillBoost37 is a glorious beacon of lightBillBoost37 is a glorious beacon of lightBillBoost37 is a glorious beacon of lightBillBoost37 is a glorious beacon of light
Default

I agree that it sounds like a classic vats turning off the fuel. Although..I am unsure what your year does to combat theft.
BillBoost37 is offline   Reply With Quote
Old 04-09-2007, 10:33 AM   #60
Member
Posts like a V-Tak
Thread Starter
 
Join Date: Jul 2006
Location: killeen texas
Posts: 49
Thanks: 0
Thanked 0 Times in 0 Posts
kyrt320 is on a distinguished road
Default

ok so any ideas on how to fix that?
kyrt320 is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Problems, Problems, Problems... swartlkk 2000-2005 2 11-04-2005 08:57 PM
Series 2 L67 Engine cover on a Series 1 L67? DJ SHO Performance, Brainstorming & Tuning 7 07-19-2004 04:39 PM
problems, problems, problems big_boss2010 1992-1999 15 04-25-2004 09:05 PM
First 04 MC SS kill? L67 II vs. L67 I! willwren General GM Chat 20 11-15-2003 07:48 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 05:04 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.