GMC/Chevrolet Truck/SUV When starting new posts, please specify YEAR, MAKE, MODEL, ENGINE type, and whatever modifications you have made.

89 K1500 ECM fuse keeps blowing

Thread Tools
 
Search this Thread
 
Old 06-08-2023, 03:05 PM
  #1  
Junior Member
Thread Starter
 
Swumpman's Avatar
 
Join Date: Jun 2023
Posts: 7
Received 8 Likes on 7 Posts
Swumpman is on a distinguished road
Cool 89 K1500 ECM fuse keeps blowing

New to the club have problem with ECM fuse keeps blowing?
89 K1500 ECM fuse will blow when I put 10 or 15 amp fuse in. When I put a 20 amp fuse in it will not blow. Installed a New Crate GM engine 5.7, Transmission rebuilt 700r4, rebuilt rear end 8.6 10 bolt 3.73 Ratio. Installed new ECM, ESC, knock sensor, Temp sensor, Oil pressure sensor. It'* running good but worried about 20 amp fuse? I did the work myself. I've been looking for a crimped wire all ground straps are new, clean and sanded where the ECM grounds at the thermostat housing bolts. Any help would appreciate.
The following users liked this post:
CathedralCub (06-08-2023)
Old 06-08-2023, 03:49 PM
  #2  
Senior Member


True Car Nut
 
carfixer007's Avatar
 
Join Date: Dec 2018
Location: Flint, MI USA
Posts: 2,790
Received 1,127 Likes on 995 Posts
carfixer007 is on a distinguished road
Default

I'd start disconnecting things until you find the short. You may be asking for trouble with that fuse.
Here'* wiring diagrams.


The following 2 users liked this post by carfixer007:
CathedralCub (06-08-2023), Swumpman (06-09-2023)
Old 06-09-2023, 10:26 AM
  #3  
Junior Member
Thread Starter
 
Swumpman's Avatar
 
Join Date: Jun 2023
Posts: 7
Received 8 Likes on 7 Posts
Swumpman is on a distinguished road
Default

Thanks for the response, I should note that 10 or 15 amp blows when driving and not all the time when riding around town. Idling in the shop it want blow. Just wondering when it goes into over-drive is that blowing it. Off work for a few days will take it back out to see if I can find exactly when it blows. ..and THANKS for the wiring diagram!
The following users liked this post:
CathedralCub (06-10-2023)
Old 06-09-2023, 06:37 PM
  #4  
Senior Member


True Car Nut
 
carfixer007's Avatar
 
Join Date: Dec 2018
Location: Flint, MI USA
Posts: 2,790
Received 1,127 Likes on 995 Posts
carfixer007 is on a distinguished road
Default

Since it doesn't use a TCM but the ECM handles the tranny it could be the TCC solenoid may cause a problem.
You have a scan tool? If so, you can watch it.

Last edited by carfixer007; 06-09-2023 at 06:38 PM.
The following users liked this post:
CathedralCub (06-10-2023)
Old 06-09-2023, 07:35 PM
  #5  
Junior Member
Thread Starter
 
Swumpman's Avatar
 
Join Date: Jun 2023
Posts: 7
Received 8 Likes on 7 Posts
Swumpman is on a distinguished road
Default

Yes I am looking into that, replacing motor, trans and rear end it could be anywhere. Will take out and drive it in 3rd gear see if I can get it to blow? If not put it in OD see if it blows. Thanks will keep this post updated till I find the short. Thanks again.
The following 2 users liked this post by Swumpman:
carfixer007 (06-09-2023), CathedralCub (06-10-2023)
Old 06-10-2023, 11:34 AM
  #6  
Junior Member
Thread Starter
 
Swumpman's Avatar
 
Join Date: Jun 2023
Posts: 7
Received 8 Likes on 7 Posts
Swumpman is on a distinguished road
Default

What scan tool will work? This is a OBD-1. Thanks.
The following users liked this post:
CathedralCub (06-11-2023)
Old 06-10-2023, 12:57 PM
  #7  
Senior Member


True Car Nut
 
carfixer007's Avatar
 
Join Date: Dec 2018
Location: Flint, MI USA
Posts: 2,790
Received 1,127 Likes on 995 Posts
carfixer007 is on a distinguished road
Default

GM has a data stream for this. Any Tech I type tool will read it.
The following users liked this post:
CathedralCub (06-11-2023)
Old 06-11-2023, 11:41 AM
  #8  
Senior Member


True Car Nut
 
CathedralCub's Avatar
 
Join Date: Feb 2015
Location: Earth
Posts: 5,582
Received 876 Likes on 805 Posts
CathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to behold
Default

I just had a thought:

How old is the battery?

What are the conditions of the battery cables and grounds?

How old is the alternator?

Maybe put a real volt meter on it and see if it is running around at a low system voltage. Low volts equals high amps equals blown fuses.
Old 06-13-2023, 01:16 PM
  #9  
Junior Member
Thread Starter
 
Swumpman's Avatar
 
Join Date: Jun 2023
Posts: 7
Received 8 Likes on 7 Posts
Swumpman is on a distinguished road
Default

Thanks for the reply: Battery is new, alternator has been in there for awhile at least 12 years. Alternator voltage is 13.85.
The following users liked this post:
CathedralCub (06-14-2023)
Old 06-14-2023, 12:27 AM
  #10  
Senior Member


True Car Nut
 
CathedralCub's Avatar
 
Join Date: Feb 2015
Location: Earth
Posts: 5,582
Received 876 Likes on 805 Posts
CathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to beholdCathedralCub is a splendid one to behold
Default

Moved thread from the "Chevrolet" forum to the "GMC/Chevrolet Truck/SUV" forum.


Quick Reply: 89 K1500 ECM fuse keeps blowing



All times are GMT -4. The time now is 04:35 AM.