Removing stubborn bolts
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2006
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Removing stubborn bolts
Well, I decided it was time to replace my wheel bearing since it was starting to go bad now that I am on break from school. Got the axle nut off no problem, wheel off, and now I'm to the caliper. I've been spraying the two T-60 bolts for two days now and they won't budge. I tried using a cheater bar and broke the T-60 socket but didn't damage the head thankfully. Next I tried some heat to expand the casting then cool the bollt, which didn't seem to do much. And lastly I tried using an impact wrench and still nothing. Not to mention this whole time I've been continually spraying it with the PB and "tapping" it with a hammer to "shock it".
I already have the wheel bearing and I don't have the money to pay someone else to do it. I think I'm just going to keep spraying it and try to get a better impact from my dads buddy. Anybody have any suggestions??
I already have the wheel bearing and I don't have the money to pay someone else to do it. I think I'm just going to keep spraying it and try to get a better impact from my dads buddy. Anybody have any suggestions??
#2
RIP
True Car Nut
The last time I had a situation like that, the grease had solidified inside the bracket and pretty much "welded" the bolt in. I had to replace the bracket.
I don't recall if the bolts on your car will have enough room, but if they are ones that stick out of the boot some, I've resorted to putting a small pipe wrench with a pipe extension on the end to get them out. Of course, the bolts have to be replaced after that.
I don't recall if the bolts on your car will have enough room, but if they are ones that stick out of the boot some, I've resorted to putting a small pipe wrench with a pipe extension on the end to get them out. Of course, the bolts have to be replaced after that.
#4
Senior Member
Posts like a Northstar
Join Date: Apr 2004
Posts: 606
Likes: 0
Received 0 Likes
on
0 Posts
I had the same problem with my rear caliper on my old Lumina. We did finally get it out but I would bet that the strength of the bracket was compromised because of all the heat we used. Replacing the bracket is the safe way to go. Or maybe you will have to drill it out? Probably not much room to do that with it on the car though.
#5
Senior Member
Posts like a Northstar
Join Date: Oct 2004
Location: Purgatory
Posts: 533
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BillBoost37
Being that you are lookin at it backwards. Are you sure that you are loosening it and not tightening it?
#6
DINOSAURUS BOOSTUS
Expert Gearhead
Originally Posted by Greyhare
Originally Posted by BillBoost37
Being that you are lookin at it backwards. Are you sure that you are loosening it and not tightening it?
#7
Member
Posts like a V-Tak
Join Date: Dec 2006
Location: Minnesota
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
Niether have I.
If it is just stuck that tight and you are going the right way, borrow someones Snap-On T-60. If that breaks, your screwed. The guys tool is warrantied, so he is good...but your screwed.
If it is just stuck that tight and you are going the right way, borrow someones Snap-On T-60. If that breaks, your screwed. The guys tool is warrantied, so he is good...but your screwed.
#8
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2006
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Yes, I am sure that I'm going the right way. I kept telling myself that I could be going the wrong way so I fake did it like I was working of something in front of me and then just flipped the ratchet/impact wrench around.
Sounds like there is no miracle cure..... Would there be any specific way to help get it out if it had loc-tite applied to the bolt? I know it had been replaced before so who knows how it was put back in
Chinski : How exactly did you go about using your heat method?
Sounds like there is no miracle cure..... Would there be any specific way to help get it out if it had loc-tite applied to the bolt? I know it had been replaced before so who knows how it was put back in
Chinski : How exactly did you go about using your heat method?
#9
Senior Member
Certified Car Nut
Join Date: Jul 2003
Location: Robbinsdale, MN
Posts: 15,408
Likes: 0
Received 0 Likes
on
0 Posts
I've heard of the heat method. You apply heat (small butane torch, etc) to soften the metals and kinda cook the rust off. Problem is, you got brake lines and stuff in that area with flamable liquids running through them
Which brings me to the product I saw on Two Guys Garage this weekend. Freeze-Off™ Super Penetrant
Which brings me to the product I saw on Two Guys Garage this weekend. Freeze-Off™ Super Penetrant
A unique formula that immediately drops the temperature of the area in direct contact with the spray. The freezing effect cracks rusted surfaces, allowing Freeze-Off™ to reach deeper & work more effectively than other penetrants.
#10
Heating or freezing, the idea is the same, to crack the rust bond and free up the fastener.
You usually have to heat it up till it smokes and turns red.
If that doesn't work, then cutting and drilling is the last ditch effort.
You usually have to heat it up till it smokes and turns red.
If that doesn't work, then cutting and drilling is the last ditch effort.