trying to get dirty, HELP!
03-23-2006, 08:56 PM
#11
Junior Member
Posts like a Ricer Type-R
Dealer for the outlet gasket, red gasket maker (goop), o-rings (coolant bypass and fuel injector kit), and oil.
www.zzperformance.com
www.intense-racing.com
www.rollingperformance.com
www.texasthunderbirds.com
All 4 of these would be a good choice for a coupler. Do NOT buy your gasket from them. They don't support your year.
www.zzperformance.com
www.intense-racing.com
www.rollingperformance.com
www.texasthunderbirds.com
All 4 of these would be a good choice for a coupler. Do NOT buy your gasket from them. They don't support your year.
03-26-2006, 12:11 PM
#12
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2006
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
Well the time has come to install my SC, I have everything cleaned and ready for gaskets. Does the SC and TB gaskets go on dry, (no gasket goo), and do I need to grease the 2 rubber yellow o-rings or do I just drop them in place on the manifold? I have also found that the "pulley key" has broken, can I find that half moon key at any hardware store?? Thanks again for all the help! 
03-26-2006, 12:19 PM
#13
Junior Member
Posts like a Ricer Type-R
Dry for the TB and SC gaskets. Make sure you torque them in the proper sequence and to the proper value for a proper seal. O-rings (yellow) drop in dry.
Fuel injector o-rings can be prelubed lightly with motor oil in order to seat properly.
Best bet for the key is to take pieces or measurements and find a local machine shop or heavy equipment repair shop. They'll probably give you one.
Otherwise get one at www.mcmaster.com
Fuel injector o-rings can be prelubed lightly with motor oil in order to seat properly.
Best bet for the key is to take pieces or measurements and find a local machine shop or heavy equipment repair shop. They'll probably give you one.
Otherwise get one at www.mcmaster.com
03-26-2006, 12:35 PM
#15
Junior Member
Posts like a Ricer Type-R
03-29-2006, 12:09 PM
#16
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2006
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
Sorry to bug u again Will, but I ordered a Coupler from rollingperformance.com on sunday and still no shipment. Do u know if this site is a pain to order from? I cant even confirm that it'* been shipped? is this normal or should I start emailing some contacts over there?
03-29-2006, 12:47 PM
#19
DINOSAURUS BOOSTUS
Expert Gearhead
I got my stuff from Rollingperformance. Very good to deal with..stuff comes quickly. If you ordered on Sunday, it probably shipped Monday and like Willwren said..2-3 days.
Be patient as you only ordered it Sunday.
Be patient as you only ordered it Sunday.
03-29-2006, 01:06 PM
#20
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2006
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
just got the mail, IT'* HERE. So in the garage I go. May the "Wrenching Gods" have mercy on me!! I say that because I broke my only torque wrench, so I hope I get it firm enough, both nosedrive and intake. I should be fine if I finger tighten then wrench starting from the center and then star patern out?, right? lol