3800 series 1, 89 Sword w/engine knock
I was updating the engine tuneup by clearing the OBD1 codes, EGR and low power...
The last tasks were plugs & wires....it seemed to have worked for only a few minutes to an hour @the most. The idle seems fine and the accelerator peddle indicated a LOT more power...but an engine knock appeared...rather loud @that....:rolleyes: I checked the OBD1 codes again...Check cam sensor and/or knock sensors:eek: Did this to both...even replaced them w/spares from the bone yard...but the engine knock it still present. Since this engine doesn't have any mechanical way to adjust the timing/dwell from a distributor....I am seeking advise from other members who have had experiences w/engine knock....:thumbup2 I had given up on the engine knock being from the cam or knock sensor...for a nosier or loose valve lifters.... So I cleaned them w/commercial solutions...dropped the oil pan for inspection & cleaning...;) Found some very fine metal shaving...but nothing unexpected for 245,000 miles...the lower end of the pistons looked clean & nothing loose...Nice & tight looking... W/new oil filter, fluids & conditioners...the engine knock is about 1/2 the volume level but still there...the idle is still smooth but the accelerator power is fairly weak. OBD1 is still giving the cam & knock sensor "alarm"...!!! My Haynes repair manual has been somewhat helpful but it is fairly generic for specific "solutions"....:rolleyes: I would like to keep the old Sword alive but I don't want to "pour" hundreds of dollars into a deepening HOLE...:confused: Any thoughts, experience or knowledge about engine knock solutions would be greatly appreciated...Thanks |
Is this a knock you can hear? Is it lower in the engine? You said you found metal in the oil. What's your oil pressure?
|
The engine knock appears to be on the lower end of the engine....No I have not done an oil pressure test .
The engine knock seems to be present mostly when there is not "peddle" pressure...if that's of some help Thanks for the rapid reply & question(s)... |
When I get home I will post a video and you tell me if that's what yoru hearing.
|
1989 LeSabre 3.8 L engine knock
I'll try to post a video clip w/audio of my engine knock....Couldn't find a way to attach it here...Sorry
I have a "cold start" (it's 100 degrees @the moment...!)....idle w/a few pushes on the accelator peddle.... Then the ignitian is turned off....a re-start is made w/a few pushes on the accelator peddle again...:rolleyes: This time I did notice that the engine knock is present during the entire time it is 'running'...not just @the idle time. You just can not hear the engine knock as much because of the louder noise coming from the EGR valve....I'll have to inspect & test that again but it doesn't throw a OBD1 code anymore. |
2 Attachment(s)
Hard to hear in this video.
https://www.gmforum.com/attachment.p...ine=1311728780 This one you can really hear. https://www.gmforum.com/attachment.p...ine=1311728780 |
Sounds like I have heard your engine before...
Hi Danthurs:
Yes, Yes....that sounds very similar to my engine knock...;) So have you solved your engine knock....? I noticed you used photobucket to post your videos...I'll try that for my short video clip to compare or hear my engine knock...straight from the old Sword...:thumbup2 |
another video attempt
Let's try this again...still having issues....:confused:
So here is a link to photo-bucket: http://s1139.photobucket.com/albums/n545/embassary2002/ Hope this is working...:cool: |
That sounds like you spun a bearing.
|
Yep, that sound is not a good sound. That sound is a rod bearing.
|
All times are GMT -4. The time now is 10:37 PM. |
© 2024 MH Sub I, LLC dba Internet Brands