switch to turn sub on/off?
#13
Senior Member
Certified GM nut
ur deck only has
Three Sets of 4-Volt RCA Preouts (Front, Rear, and Sub) just like mine
what i meant though was at least 4v outputs. but i've never seen a deck/amp combination that takes 16v
Three Sets of 4-Volt RCA Preouts (Front, Rear, and Sub) just like mine
what i meant though was at least 4v outputs. but i've never seen a deck/amp combination that takes 16v
#14
Senior Member
Posts like a Camaro
Join Date: Aug 2003
Location: Sunshine State
Posts: 801
Likes: 0
Received 0 Likes
on
0 Posts
I didn’t imply that I did have 16 volt pre-outs; I am aware of the specs of my equipment, after all it’* in my signature. You’d think I would know what I have, but thanks for pointing it out anyway.
Eclipse has for a long time had some of the highest pre-outs available. The owner of the audio shop I frequent has an eclipse with 16volt outputs. Any amp should accept the signal, I think the theory behind it is the AMP doesn’t have to work as hard? or it can amplify even more? Not sure, but here is an Eclipse with 16v
http://www.canze.org.nz/reviews/inde...roduct_ID=1035
My only point in bringing all this up is 1994SE was looking for a very economical solution (a $3 switch) to suggest that he upgrade his HU so he has on/off control, phase control, and have 4volt outputs, etc. just seems excessive, so I sarcastically suggested a 16volt HU instead...
I am just joking around with ya, hope you don't take me seriously..
Eclipse has for a long time had some of the highest pre-outs available. The owner of the audio shop I frequent has an eclipse with 16volt outputs. Any amp should accept the signal, I think the theory behind it is the AMP doesn’t have to work as hard? or it can amplify even more? Not sure, but here is an Eclipse with 16v
http://www.canze.org.nz/reviews/inde...roduct_ID=1035
My only point in bringing all this up is 1994SE was looking for a very economical solution (a $3 switch) to suggest that he upgrade his HU so he has on/off control, phase control, and have 4volt outputs, etc. just seems excessive, so I sarcastically suggested a 16volt HU instead...
I am just joking around with ya, hope you don't take me seriously..
#15
Senior Member
Certified GM nut
alpine mrv-f10008.5 Volt Input Capability
Rockford 1001bd - Voltage -150mV - 6 volts
notice no eclipse amps say they accept the ENORMOUS 16v input capability
i don't think you could physically hear any difference in sound quality of 4-6v preouts
ok but enough thread stealing....goodtimes
Rockford 1001bd - Voltage -150mV - 6 volts
notice no eclipse amps say they accept the ENORMOUS 16v input capability
i don't think you could physically hear any difference in sound quality of 4-6v preouts
ok but enough thread stealing....goodtimes
#17
Senior Member
Posts like a Turbo
Join Date: Dec 2003
Location: INDIANA
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
yes the eclispe pre out are 16 volts. most amps i have seen will accept as high as 8 but i have seen none that go to 16. as far as the swicth for the subs yes i would place it on the remote turn on wire if your head unit does not do so. i can turn my sub on and off as well as adjust the signal through my headunit. that is the best why if possible
Thread
Thread Starter
Forum
Replies
Last Post
methatswho
Pontiac
3
03-15-2015 08:26 PM
raptor660
Audio (and aftermarket electronics)
18
07-08-2011 07:29 PM
Hans
Everything Electrical & Electronic
19
01-26-2007 08:27 PM
STROKER
Performance, Brainstorming & Tuning
1
09-02-2005 11:57 AM