Can OEM exhaust manifold crack be repaired?
#1
Senior Member
Posts like a Northstar
Thread Starter
Can OEM exhaust manifold crack be repaired?
The engine on my '92 SSE */c was rebuilt shortly before I bought it, and the receipt noted that the exahust manifold was cracked. I looked at the front manifold at that time and didn't see a crack so I didn't think I needed to worry about it...until now (see my other post about SES and error code 44). The car has had a rough idle since I've owned it, but hasn't had any other longstanding driveability problems.
I replaced the rear valve cover gasket a few days ago, along with the plugs and wires, and I saw a small gap, maybe 1/16") in part of the welded joint near the o2 sensor, and now that I'm getting an SES error code 44 (o2 sensor lean) I wonder if maybe the crack is getting worse and needs to be repaired. The crack is upstream, a few inches before the o2 sensor joint. By the way, the plugs looked good after 40,000 miles, hardly worn electrodes, all same grayish color.
Can the OEM exhaust pipe be welded at a muffler shop? Or is there a high temp epoxy or something I can use to fill the crack?
Thanks.
I replaced the rear valve cover gasket a few days ago, along with the plugs and wires, and I saw a small gap, maybe 1/16") in part of the welded joint near the o2 sensor, and now that I'm getting an SES error code 44 (o2 sensor lean) I wonder if maybe the crack is getting worse and needs to be repaired. The crack is upstream, a few inches before the o2 sensor joint. By the way, the plugs looked good after 40,000 miles, hardly worn electrodes, all same grayish color.
Can the OEM exhaust pipe be welded at a muffler shop? Or is there a high temp epoxy or something I can use to fill the crack?
Thanks.
#2
Junior Member
Posts like a Ricer Type-R
I would have it welded by a muffler shop. Should be very reasonable. My concern with the epoxy is that the heat would make it outgas, and possibly nuke your O2 with the fumes.
#5
Senior Member
Posts like a Northstar
Thread Starter
On a side note, it sounds like the catalytic converter recently began making the same humming noise when accelerating just like my '93 SSEi did last year, so as soon as possible I'll have the exhaust manifold welded and the catalytic converter replaced.
From what I've read on usenet today, code 44 (lean O2) isn't usually caused by a defective o2 sensor...but I hope it'* the cause of the code in my case.
From what I've read on usenet today, code 44 (lean O2) isn't usually caused by a defective o2 sensor...but I hope it'* the cause of the code in my case.
#6
Senior Member
Posts like a Northstar
Thread Starter
I called a muffler shop and was told that the exhaust manifold probably can't be welded because of the material it'* made of, and they'd have to look at it anyway to see if they can access the area in the event that it'* weldable.
In the event that it can't be welded, the guy said that he'* heard of people using JB Weld and that may work. Have any of you tried that stuff in a high temp application like this?
I bought a CarSound high flow 2 1/2" catalytic converter and will have it installed soon. And I'll ask them to take a look at the crack/gap in the exhaust manifold and suggest what to do about it. It looks like a bad factory weld job to me.
By the way, the SES error code 44 has been resolved with a new o2 sensor.
In the event that it can't be welded, the guy said that he'* heard of people using JB Weld and that may work. Have any of you tried that stuff in a high temp application like this?
I bought a CarSound high flow 2 1/2" catalytic converter and will have it installed soon. And I'll ask them to take a look at the crack/gap in the exhaust manifold and suggest what to do about it. It looks like a bad factory weld job to me.
By the way, the SES error code 44 has been resolved with a new o2 sensor.
#7
Senior Member
Posts like a Turbo
Join Date: Apr 2003
Location: Arkansas
Posts: 409
Likes: 0
Received 0 Likes
on
0 Posts
They should be able to weld it. They would need a heliark, please forgive my spelling. As for JB Weld it would probably hold it is some amazing stuff. The problem would be the 500 degree limit. There are fixes out there. Check this web page out.
http://www.muggyweld.com/castiron.html
http://www.muggyweld.com/silvercast.html
http://www.muggyweld.com/castiron.html
http://www.muggyweld.com/silvercast.html
#8
Senior Member
Certified Car Nut
Join Date: Jul 2003
Location: Robbinsdale, MN
Posts: 15,408
Likes: 0
Received 0 Likes
on
0 Posts
I used JB Weld to patch over a cracked head in a Corsica, if that'* any help. I was payin $800 plus to get the POS fixed. Sealed it right up and held for over a year until I finally talked the missus into donating the damn money pit
#9
Senior Member
Posts like a Turbo
Join Date: Jul 2003
Location: Boston Area
Posts: 327
Likes: 0
Received 0 Likes
on
0 Posts
The exhaust manifold is cast iron, I believe. In order to weld cast iron the surrounding material needs to be brought up to a high temperature. This is what I recall.
Why not just buy a new one or find one in a junkyard?
Why not just buy a new one or find one in a junkyard?
#10
Senior Member
Posts like a Northstar
Join Date: Dec 2002
Location: Western, Mass
Posts: 587
Likes: 0
Received 0 Likes
on
0 Posts
They are about 60 bucks a piece at the junkyard i went too (wanted to get some ported ones). Then you won't have to worry about a weld giving out.