Finally finished my new neon control--- CCR buttons
#1
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2003
Location: Corn Fields, IN
Posts: 2,767
Likes: 0
Received 0 Likes
on
0 Posts
Finally finished my new neon control--- CCR buttons
My neons are now controlled by the ride control buttons. I found a 3 button pod in a junkyard yesterday--the fourth junkyard i've searched.
The backlighting in the buttons is controlled by the harness that was hiding in the console, so they dim with the dash. Also, one of the LEDs lights up to tell me when the neons are on. I'm using a 30 amp relay which is overkll by about 29.5 amps, so i'm not worried about burning up anything. After all my research on bistable flipflops, it turns out that the ride control buttons are toggle on/off...
just another project made possible by the bonneville club
The backlighting in the buttons is controlled by the harness that was hiding in the console, so they dim with the dash. Also, one of the LEDs lights up to tell me when the neons are on. I'm using a 30 amp relay which is overkll by about 29.5 amps, so i'm not worried about burning up anything. After all my research on bistable flipflops, it turns out that the ride control buttons are toggle on/off...
just another project made possible by the bonneville club
#3
Senior Member
True Car Nut
Join Date: Aug 2004
Location: In your garage, swipin' da lug nutz
Posts: 3,067
Likes: 0
Received 1 Like
on
1 Post
Sounds like what I was going to do with my neons too, but I also thought about using several different fog lamp switches from various pontiacs I found in the junkyard, and then yanking out all the seat switches in the center console and replace those switches with said fog switches. They fit in there perfectly, but the only downside is that I will need nine switches to fill nine holes :? And I KNOW I dont need that many anyways.
#4
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2003
Location: Corn Fields, IN
Posts: 2,767
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BonneMeMN
Which wire was the one for the dash? I'm needing to hookup my 5 button pod to lights....
http://www.bonnevilleclub.com/forum/...shifter+muster
The grey wire controls illumination for the TC button, and black #2 handles the CCR and shift mode buttons.
One major issue here is that the different generation bonnies have slightly different colored wire. I spent half the afternoon at the kitchen table with a multimeter trying to diagram this out. I never could get the LEDs on the CCR buttons to work, so i'm using the TC LED as my indicator.
#6
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2003
Location: Corn Fields, IN
Posts: 2,767
Likes: 0
Received 0 Likes
on
0 Posts
I think seven gold stars is enough for any mortal.
If anyone has any insight as to why i couldn't get the CCR LEDs to light up, please share :?
Here'* the diagram.
If anyone has any insight as to why i couldn't get the CCR LEDs to light up, please share :?
Here'* the diagram.
#7
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2003
Location: Corn Fields, IN
Posts: 2,767
Likes: 0
Received 0 Likes
on
0 Posts
I discovered why i couldn't get the LEDs to work. They are 3.6V leds. While the other three buttons have their own resistors to reduce current to LEDs, the CCR buttons do not. I used a 9V battery when i was testing them. Would this have blown them?
#8
Senior Member
Certified GM nut
Join Date: Jun 2004
Location: Grand Haven, Michigan
Posts: 1,719
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by John Deere Boy
I think seven gold stars is enough for any mortal.
If anyone has any insight as to why i couldn't get the CCR LEDs to light up, please share :?
Here'* the diagram.
If anyone has any insight as to why i couldn't get the CCR LEDs to light up, please share :?
Here'* the diagram.
#9
Originally Posted by John Deere Boy
I discovered why i couldn't get the LEDs to work. They are 3.6V leds. While the other three buttons have their own resistors to reduce current to LEDs, the CCR buttons do not. I used a 9V battery when i was testing them. Would this have blown them?
9 volts would have easily blown them, they problably flashed for half a second and then went out. if you want to make em start on fire and smoke a lot, just keep the voltage on them for a long time been there done that
Thread
Thread Starter
Forum
Replies
Last Post