GM Forum - Buick, Cadillac, Olds, GMC & Pontiac chat - Search Results

Search: Posts Made By: Danthurs
Showing results 1 to 16 of 16
Search took 0.02 seconds.
06-14-2011, 06:08 PM
Replies: 0
Views: 7,079
Posted By Danthurs

ICM and crank position test

I just finished up a write up on testing the ignition control module, and also has in it how to test a crankshaft position sensor. Here is the link to it in tech info.
...
06-08-2011, 07:59 PM
Replies: 0
Views: 38,418
Posted By Danthurs

ICM test

Testing the Ignition Control Module (ICM)


https://www.gmforum.com/howto/ICM/master.JPG
Each circuit is described by a letter. If you look closely at the connector (on the car)...
05-10-2011, 09:34 PM
Replies: 0
Views: 9,473
Posted By Danthurs

P1406

P1406

Description
EGR pintle performance

Symptoms
can cause driveability, performance, mileage, and emissions issues.

Causes
Forum: Mechanical
02-03-2011, 09:12 PM
Replies: 0
Views: 8,761
Posted By Danthurs

UIM and LIM gaskets L36

Disconnect the negative battery cable.

Remove the upper radiator hose and then use a shop vac to suck out some of the coolant.

Remove the cap from the shreader valve and then bleed off the fuel...
Forum: Mechanical
12-08-2009, 12:34 PM
Replies: 0
Views: 9,310
Posted By Danthurs

Harmonic balancer replacement

Jack up the passenger side of the car and remove the wheel
https://www.gmforum.com/howto/tech-info/t278822/P9060001.jpg

Remove the splash guard....
11-02-2009, 09:48 AM
Replies: 0
Views: 4,169
Posted By Danthurs

Starter Solenoid Clicks, Engine Does Not Crank

Check the battery and starter motor terminals for corrosion or poor contact.
Remove the INJECTOR Fuse 7 from the RH I/P Power Distribution Center to prevent the engine from starting.
Place the...
10-02-2009, 11:50 AM
Replies: 0
Views: 27,084
Posted By Danthurs

Throttle position sensor (TPS) replacement

Locate your TPS on the side of the throttle body.

The unplug the sensor by lifting on the tab and then wiggle and pull the plug, do not pull on the wires....
09-27-2009, 02:23 PM
Replies: 0
Views: 8,277
Posted By Danthurs

P0530

P0530

Description
A/C REFRIGERANT PRESSURE SENSOR CIRCUIT


PCM uses input signal from A/C refrigerant pressure sensor to
determine if it should turn on engine coolant fans. When signal is...
09-27-2009, 12:34 PM
Replies: 0
Views: 17,980
Posted By Danthurs

P1665

P1665

Description
EVAP VENT SOLENOID CONTROL CIRCUIT

The Output Driver Module (ODM) is used by the PCM to turn on
many of the current-driven devices that are needed to control various...
09-27-2009, 12:07 PM
Replies: 0
Views: 13,972
Posted By Danthurs

P1639

P1639

Description
5-VOLT REFERENCE "B" CIRCUIT

PCM uses 5-volt reference "B" circuit as a sensor feed for
A/C refrigerant pressure sensor. PCM monitors voltage on this circuit.
If PCM...
09-24-2009, 03:15 PM
Replies: 0
Views: 7,815
Posted By Danthurs

P0121

P0121

Description
TP SENSOR SYSTEM PERFORMANCE

Throttle Position (TP) sensor measures amount of throttle
opening. PCM uses TP sensor information for fuel delivery
calculations. TP sensor...
02-09-2009, 11:13 AM
Replies: 0
Views: 5,764
Posted By Danthurs

Engine trouble shooting guide

http://i300.photobucket.com/albums/nn3/dthurs2000/car/trouble%20shooting/enginepage1.jpg
30055
30056
30057
30058
30059
01-24-2009, 01:12 PM
Replies: 0
Views: 16,899
Posted By Danthurs

EVAP clean

If you think your airflow is low due to clogged passages in the evap core, your finding wet carpet, or if your car is more then 6 years old, then this is something you should do.

Before starting,...
Forum: Mechanical
01-20-2009, 11:58 AM
Replies: 0
Views: 24,423
Posted By Danthurs

Adjust AC clutch plate

If you here grinding sounds from under your hood, or your AC is cooling intermittently, you may only need to adjust your clutch and not need that $800 service visit.
...
Forum: Electrical
01-19-2009, 02:14 PM
Replies: 0
Views: 25,871
Posted By Danthurs

Bypass VATs on 92-99

92-95 if the car cranks, vats is not the issue
96-99 if the car does not crank, vats is not the issue.


If you have a VATs on your car, your key will look something like this. The small black...
01-13-2009, 02:52 PM
Replies: 0
Views: 19,126
Posted By Danthurs

2000+ torque specs

General engine data/specifications
Displacement 231 cu in (3.8l)
RPO L36
Bore 3.8 in
Stroke 3.4 in
Compression ratio 9.4:1
Firing order ...
Showing results 1 to 16 of 16


 

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.