FWI and PCM installed..PICS (56k no)
12-02-2005, 07:30 PM
#2
BANNED
Join Date: Mar 2004
Location: Purgatory
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
just guessing here... but i think you are just supposed to turn it to the on position, and not start.. then do you see the light?
try disconnecting the battery and starting over...
when you say 4k limit... do you mean rev limiter in park??? that is a GOOD thing and you want that
try disconnecting the battery and starting over...
when you say 4k limit... do you mean rev limiter in park??? that is a GOOD thing and you want that
12-02-2005, 07:33 PM
#3
Senior Member
Certified GM nut
Join Date: Sep 2005
Location: Home Sweet Home in New York
Posts: 2,009
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by harofreak00
just guessing here... but i think you are just supposed to turn it to the on position, and not start.. then do you see the light?
try disconnecting the battery and starting over...
when you say 4k limit... do you mean rev limiter in park??? that is a GOOD thing and you want that
try disconnecting the battery and starting over...
when you say 4k limit... do you mean rev limiter in park??? that is a GOOD thing and you want that
12-02-2005, 08:01 PM
#5
Senior Member Emeritus
Posts like a Camaro
Join Date: Feb 2005
Location: Grand Rapids, Iraq
Posts: 1,129
Likes: 0
Received 0 Likes
on
0 Posts
Re: FWI and PCM installed but I have a problem with the PCM.
Originally Posted by VigCS
I got all of my stuff installed tonight (FWI & PCM), but I think there'* a problem with my PCM. According to a sheet intense sent me, they said I need to do a security relearn process with my car, the first step being trying to turn on my car and letting it fall back into the "on" position where the security light should show itself.
Problem...
1) The car starts...which it isn't supposed to do when I try to start it right after installing the PCM.
2) My 4,000 rpm rev limiter is still there.
3) The security light never comes on.
I tried calling Todd but he'* out of town until the 5th. Do you think Intense acidentally sent me another stock PCM?
Pics are coming tonight.
Problem...
1) The car starts...which it isn't supposed to do when I try to start it right after installing the PCM.
2) My 4,000 rpm rev limiter is still there.
3) The security light never comes on.
I tried calling Todd but he'* out of town until the 5th. Do you think Intense acidentally sent me another stock PCM?
Pics are coming tonight.
4k limiter will always be there to protect from grenading the engine in idle
Now on the CASE learn, Im not peticularly sure, since the 97 GTPs dont need a case learn, but Im not sure if the 97 B-ville would be the same. I doubt it will assuming the GTP and Bonneville for the 97 are the same, minus the obvious body differences.
12-02-2005, 08:13 PM
#7
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Mar 2005
Location: Frederick, Maryland
Posts: 1,441
Likes: 0
Received 0 Likes
on
0 Posts
I'm still confused as to why I didn't have to do a security re-learn. I'll try what haro suggested in the morning.
12-02-2005, 08:48 PM
#8
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Mar 2005
Location: Frederick, Maryland
Posts: 1,441
Likes: 0
Received 0 Likes
on
0 Posts
Ok, here come the pics....
This has to go...
Gone!
Down in there with the airbox gone.
Tube off of throttle body.
Charcoal canister out of its hole.
Hole!
Up in the air
PCM Hookups
Coupler on (throttle body clamp replaced with stock one in final pic, intense provided clamp didn't tighten enough)
Better view
Even better view
Agh! It'* too long! (hacksaw was the solution)
Filter from above
Relocated IAT
Intake is finished!
The filter
The final setup (PCM and Charcoal canister relocated)
<Peter Griffin> Alriiight </Peter Griffin>
Last pic up on the lift (That guy was helping me out)
A triumphantly blurry pic of me with my best friend, the impact wrench.
This has to go...
Gone!
Down in there with the airbox gone.
Tube off of throttle body.
Charcoal canister out of its hole.
Hole!
Up in the air
PCM Hookups
Coupler on (throttle body clamp replaced with stock one in final pic, intense provided clamp didn't tighten enough)
Better view
Even better view
Agh! It'* too long! (hacksaw was the solution)
Filter from above
Relocated IAT
Intake is finished!
The filter
The final setup (PCM and Charcoal canister relocated)
<Peter Griffin> Alriiight </Peter Griffin>
Last pic up on the lift (That guy was helping me out)
A triumphantly blurry pic of me with my best friend, the impact wrench.
12-02-2005, 10:15 PM
#10
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Mar 2005
Location: Frederick, Maryland
Posts: 1,441
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by dcjredline
Nice. How is it? Work well?