Leaking Coolant, odd location
#1
Senior Member
True Car Nut
Thread Starter
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Leaking Coolant, odd location
I want to get a 2nd opinion from you guys:
What I posted on the Explorer Forum:
I was told it is the "Heater Control Valve"
Sound right?
thanks guys!
What I posted on the Explorer Forum:
Originally Posted by 96ExplorerXL4x4
Ok, went to jump start my car with the explorer. Had the hood poped, was keeping the engine reved a bit at a steady 2000RPM when all the sudden I started to see a small steam cloud coming from the engine bay
Shut the motor off and went to take a look.
Here'* what I found.
without flash:
with flash:
Looks to be coming from the wierd actuator, or one of the lines feeding it...
Safe to still drive it?
Any input/help is much apriciated!
Thanks!
-John
Shut the motor off and went to take a look.
Here'* what I found.
without flash:
with flash:
Looks to be coming from the wierd actuator, or one of the lines feeding it...
Safe to still drive it?
Any input/help is much apriciated!
Thanks!
-John
Sound right?
thanks guys!
#2
Senior Member
True Car Nut
Join Date: Feb 2006
Location: Melrose
Posts: 4,596
Likes: 0
Received 0 Likes
on
0 Posts
It definatley looks like some part of the heating/cooling system since it has both inlets and outlets. Maybe time to remove it and see if theres a crack on the underside of the plastic Piece.
#3
Senior Member
True Car Nut
That sounds about right!
Before doing too much, try to determine exactly where the leak is. It could be a pinhole in a heater/coolant hose, a loose connector (not too likely), or even a crack in the actuator itself. You may find that that actuator part is not cheap.
Depending on the size of the leak, you could continue driving it for short trips. Mind you that I hesitate to say this, because without knowing where the actual leak is, you can't evaluate the severity of the situation. If it'* a crack in the plastic part, it has the potential to catastrophicly fail under further use.
If it were me, I would do my best to locate the exact failure area and get it repaired. I don't like taking chances with large $ items that I count on every day.
Before doing too much, try to determine exactly where the leak is. It could be a pinhole in a heater/coolant hose, a loose connector (not too likely), or even a crack in the actuator itself. You may find that that actuator part is not cheap.
Depending on the size of the leak, you could continue driving it for short trips. Mind you that I hesitate to say this, because without knowing where the actual leak is, you can't evaluate the severity of the situation. If it'* a crack in the plastic part, it has the potential to catastrophicly fail under further use.
If it were me, I would do my best to locate the exact failure area and get it repaired. I don't like taking chances with large $ items that I count on every day.
#4
Senior Member
True Car Nut
Thread Starter
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the replys guys!
Unfortunatly, the bonnie isn't in running condition, so I had to drive it to school. Once/If I get home (another 20 minute drive) I'm going to look into it more closely.
<--- Crosses fingers
Unfortunatly, the bonnie isn't in running condition, so I had to drive it to school. Once/If I get home (another 20 minute drive) I'm going to look into it more closely.
<--- Crosses fingers
#6
Senior Member
True Car Nut
Thread Starter
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by lash
Just make sure that before you take of for home today, you check your coolant level. Then pay close attention during your drive.
I was very diligent on the way to school today; esp looking at the temp. gauge
#8
Senior Member
True Car Nut
Join Date: Dec 2005
Location: August 07 COTM....NEBF '06, CEBF '06 OHMM '06 ONBF '07 CEBF '07
Posts: 4,064
Likes: 0
Received 0 Likes
on
0 Posts
Guys, guys.
You're overworking your feeble brains...the answer is right there.
The answer is: Ford
John, I kid I kid.
You're overworking your feeble brains...the answer is right there.
The answer is: Ford
John, I kid I kid.
#10
Senior Member
True Car Nut
Thread Starter
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by PEARL_JAM
That control valve is seamed plastic. They often crack at these seams.
Thread
Thread Starter
Forum
Replies
Last Post