The shop project
#1
Retired Senior Admin
Expert Gearhead
Thread Starter
Join Date: May 2006
Location: Sheboygan Wisconsin
Posts: 29,661
Likes: 0
Received 28 Likes
on
24 Posts
The shop project
OK, so I finally decided to rebuild my shop. Going to be a big project, but it really needs to be done. As it is it'* simply to packed full and not enough room to move around.
Well, to start it off. My Christmas present was a new tool box. But it'* been back ordered. My wife stopped in Friday, nope, still don't have any. Well, today I needed to pick up some PCV pipe to do some plumbing in the basement. And I figure, what harm in looking. Nope, none on the shelf. No harm in asking. Any idea when your going to get that box? No, we have no idea. I said you know, I'll even take the display model. She said I'll take a look. Looks on the computer and says, hey, says here I have one sitting on a skid in back. Can I have it? You sure can. Yippy, I drive around the back to get loaded. They actually had 2, must have just come in. What luck.
DSC03572.jpg
OK, small problem, they loaded it with a forklift. No big deal, I have tools.
DSC03573.jpg
Just like Christmas.
DSC03574.jpg
That gives me 8 feet of tool box. Should cover me for a little while.
DSC03575.jpg
Need to pick up some 2x4 and build a new bench off to the right of where I have it now. The tool box will be going under the bench. I'm happy now.
Well, to start it off. My Christmas present was a new tool box. But it'* been back ordered. My wife stopped in Friday, nope, still don't have any. Well, today I needed to pick up some PCV pipe to do some plumbing in the basement. And I figure, what harm in looking. Nope, none on the shelf. No harm in asking. Any idea when your going to get that box? No, we have no idea. I said you know, I'll even take the display model. She said I'll take a look. Looks on the computer and says, hey, says here I have one sitting on a skid in back. Can I have it? You sure can. Yippy, I drive around the back to get loaded. They actually had 2, must have just come in. What luck.
DSC03572.jpg
OK, small problem, they loaded it with a forklift. No big deal, I have tools.
DSC03573.jpg
Just like Christmas.
DSC03574.jpg
That gives me 8 feet of tool box. Should cover me for a little while.
DSC03575.jpg
Need to pick up some 2x4 and build a new bench off to the right of where I have it now. The tool box will be going under the bench. I'm happy now.
#3
-- SITE DONATOR --
True Car Nut
Fits right in! Also reminds me I need to go get another tool box. Unfortunately it'* going to be a while before I have room for anything that big. I'm just picking up something to organize some wrenches and screw drivers in.
Are you going to extend the bench from where it is to cover over the tool boxes as well, or just building a new one?
Are you going to extend the bench from where it is to cover over the tool boxes as well, or just building a new one?
#4
Retired
I got some 2x4'* over here if you want them Dan. You just have to come pick them up.
Ugh, I can't wait until it gets warmer so I can work out in my garage again!
Ugh, I can't wait until it gets warmer so I can work out in my garage again!
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#5
Retired Senior Admin
Expert Gearhead
Thread Starter
Join Date: May 2006
Location: Sheboygan Wisconsin
Posts: 29,661
Likes: 0
Received 28 Likes
on
24 Posts
A new bench is going to be built. It will start about the middle of the right most box, and go about 11 feet, perhaps 12 to the wall. Then round the corner and another 8 feet till it gets to my compressor. I want the center stall totally open.
#8
Retired
6inch deep drawer to accomadate your most used tools
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#9
Retired Senior Admin
Expert Gearhead
Thread Starter
Join Date: May 2006
Location: Sheboygan Wisconsin
Posts: 29,661
Likes: 0
Received 28 Likes
on
24 Posts
Spent the morning cleaning up. Then started framing up the work bench. First I laid it out.
DSC03590.jpg
Framed in the first section.
DSC03593.jpg
Then framed in the other section.
DSC03594.jpg
That'* all I got so far today. Need to pick up the plywood for the top yet. Still need to get a few more braces here and there. Just not enough hours in the day.
DSC03590.jpg
Framed in the first section.
DSC03593.jpg
Then framed in the other section.
DSC03594.jpg
That'* all I got so far today. Need to pick up the plywood for the top yet. Still need to get a few more braces here and there. Just not enough hours in the day.