Did some more matainance on the brothers car
#1
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
Did some more matainance on the brothers car
I knew the TB would be dirty but didnt figure it would be this dirty (only had 87K on it)
So we cleaned it and gave it a nice shine. Also cleaned the MAF, and i cleaned the inlet of the supercharger. The car feels like it has much better throttle response now
So we cleaned it and gave it a nice shine. Also cleaned the MAF, and i cleaned the inlet of the supercharger. The car feels like it has much better throttle response now
#2
Junior Member
Posts like a Ricer Type-R
Leave the SC inlet the way it was in the future. The carbon buildup actually 'fills' the rough sand casting on the inlet that is responsible for increased temps under boost.
How'* the idle? Every time I've cleaned a TB and IAC, my idle has always smoothed out, even though I didn't think it was bad before.
How'* the idle? Every time I've cleaned a TB and IAC, my idle has always smoothed out, even though I didn't think it was bad before.
#3
Senior Member
Posts like a Camaro
Join Date: Oct 2006
Location: montreal canada NEBF07 ONBF07
Posts: 987
Likes: 0
Received 0 Likes
on
0 Posts
that should help a lot did you take any after pict of it clean and did you install the PEM to next time you should run in the 14 my TB ready to
#4
Senior Member
Certified GM nut
Thread Starter
Join Date: Dec 2002
Location: plattsburgh NY
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
Wren, that does make sense actually. Thank you for the advice.
So when you get a supercharger ported and polished, i am assuming that the inlet porting is cleaning up that rough casting. That is not the prettiest thing i have ever seen . What is done on the outlet? Pretty much the same thing, getting rid of the roughness, and also opening up the ends to make a triangle correct?
And yes it does idle much smoother.
Don, no after pics sorry. We were rushing, had to get some late season mowing in at my house. And we didnt get to the front pem yet, maybe this week though. I definently think the car has a 14 second pass in it the way it is. I hit that 15.20 and that wasnt on a pretty launch. With a little better launch i know a 15 flat was possible. And that was FULL weight (including spare, jack, and alot of misc stuff in the car), also head light was in and that wasnt helping.
So when you get a supercharger ported and polished, i am assuming that the inlet porting is cleaning up that rough casting. That is not the prettiest thing i have ever seen . What is done on the outlet? Pretty much the same thing, getting rid of the roughness, and also opening up the ends to make a triangle correct?
And yes it does idle much smoother.
Don, no after pics sorry. We were rushing, had to get some late season mowing in at my house. And we didnt get to the front pem yet, maybe this week though. I definently think the car has a 14 second pass in it the way it is. I hit that 15.20 and that wasnt on a pretty launch. With a little better launch i know a 15 flat was possible. And that was FULL weight (including spare, jack, and alot of misc stuff in the car), also head light was in and that wasnt helping.
Thread
Thread Starter
Forum
Replies
Last Post
TJ'sblackbonne
General GM Chat
15
09-30-2007 08:53 PM
chromebonne32
Your Ride: GM Pictures & Videos
6
09-16-2007 09:14 PM
salmanman
Your Ride: GM Pictures & Videos
21
08-03-2007 08:13 AM