Rusted-out subframe mount washers (fixed!)
#1
Senior Member
Posts like a Camaro
Thread Starter
Join Date: Jan 2003
Location: Jenison, MI (Near Grand Rapids)
Posts: 1,070
Likes: 0
Received 0 Likes
on
0 Posts
Rusted-out subframe mount washers (fixed!)
I peeked under the LeSabre today, and got a bit of a shock. One of the really big curvy-stamped subframe mount washers was almost falling off! The bolt is still in there just fine. I don't have much rust under there. The washer is rusted right out though.
Anyone else have this happen?
Is that a dealer-only thing? I'm headed to the junkyard this weekend... might just steal one from there, unless someone knows a good cheap source for new.
Anyone else have this happen?
Is that a dealer-only thing? I'm headed to the junkyard this weekend... might just steal one from there, unless someone knows a good cheap source for new.
#2
Senior Member
True Car Nut
Yeah, apparently this guy just had it happen to him. Read his and you'll want to fix it right away.
http://www.bonnevilleclub.com/forum/...130&highlight=
As far as I know, those are a dealer only item and not cheap.
http://www.bonnevilleclub.com/forum/...130&highlight=
As far as I know, those are a dealer only item and not cheap.
#3
Senior Member
True Car Nut
Join Date: Jan 2006
Location: NEBF:06,07 | NYBF:06,07 | ONBF:06,07 | CNBF:06 & more............
Posts: 8,029
Likes: 0
Received 0 Likes
on
0 Posts
#4
Senior Member
Posts like a Camaro
Thread Starter
Join Date: Jan 2003
Location: Jenison, MI (Near Grand Rapids)
Posts: 1,070
Likes: 0
Received 0 Likes
on
0 Posts
Huh, OK. I had heard of the bolts and subframe rotting out, but never the washers. I suppose that if one is gone, the others might not be too far behind, eh? Here'* hoping that I can snag a handful from a virtually rust-free car in the yard this weekend.
Meanwhile, I'm telling the wife to "drive gently!" It'* just got to hang on a couple days.
Can I get that bolt out with a breaker bar and socket? I've got impact goodness at home, but not at the yard. I think I've done it before, but it'* been a couple years...
Now I'm all paranoid about all six washers on both cars! :?
It'* really strange though, that one broke on the '96, when my rusty old '89 was fine. I'm just glad I was down there spraying my fuel filter fitting with PB blaster, or I might not have noticed it until the whole drivetrain fell out.
Meanwhile, I'm telling the wife to "drive gently!" It'* just got to hang on a couple days.
Can I get that bolt out with a breaker bar and socket? I've got impact goodness at home, but not at the yard. I think I've done it before, but it'* been a couple years...
Now I'm all paranoid about all six washers on both cars! :?
It'* really strange though, that one broke on the '96, when my rusty old '89 was fine. I'm just glad I was down there spraying my fuel filter fitting with PB blaster, or I might not have noticed it until the whole drivetrain fell out.
#5
Senior Member
Posts like a Camaro
Thread Starter
Join Date: Jan 2003
Location: Jenison, MI (Near Grand Rapids)
Posts: 1,070
Likes: 0
Received 0 Likes
on
0 Posts
Well, I tackled this project over the weekend.
It should have been easy. It wasn't.
I went to a local junkyard and got a handful of the washers and bolts.
I came home and started to loosen the bolt with a breaker bar, and it started out alright. Then it got harder to turn, and with surprisingly little effort, it snapped right off.
Bummer.
And of course, the subframe mount in question is the one with no top access to the captive nut. It'* the rear-most one. Double-bummer.
So... I did what I had to do. It was either cut a hole in the inner fender, or the dead-pedal area of the floor. The floor won, since carpet hides ugly repairs better than undercoating.
To make the hole, I drilled a series of small holes very close to each other on three sides, and then punched through the remaining material with a flat blade screwdriver and hammer. Then I peeled it up like a sardine can (the sheet steel there is disturbingly thin).
From there I could see that my captive nut was held in place by a sheet metal cover of sorts, which was welded in place on two sides. Channeling my anger and frustration, I beat on it with screwdrivers, hammers, and punches until I'd cut it in half, so that I could then peel the two welded-on sides away from the nut assembly, and remove it. It'* a rather large, diamond-shaped metal plate attached to the bottom of the nut, for the record.
Reassembly went well. I was going to use a new nut and flat washers on the top side, but apparently Lowes, Home Despot, Napa, Autozone, and TSC don't think m12 x 1.75 class 10.9 nuts are an item they need to carry. I was pissed. But it motivated me to work harder to unstick the stock nut and bolt-fragment, which did work, after PB blaster, heat (repeat a few times), vise-grips, and more brute force. I am glad it worked that way, because the stock nut assembly was still large enough/bulky enough that it wouldn't turn in it'* place as I tightened it up. Score! It'* not exactly captive, it could be pushed out of the way accidentally, but if someone was careful, they could remove it and replace it again without re-opening my access hole.
Speaking of the access hole: I folded the metal back into place, and sprayed it up good with automotive primer. It looks okay, but I have a feeling there is still some exposed metal on the back side. Any suggestions for making the repair as rust-resistant as possible? I haven't fabricated a patch yet, but that is the plan. I'll just sheet-metal-screw it in place with some goop in between to seal it. I'm just concerned about water splashing up into there through the few little holes that do access that compartment from the bottom, and corroding my floor. I don't really have good access to coat the back of the repair with anything though... Any thoughts would be appreciated.
For now, it'* just folded back, with the carpet back over it, and my wife has strict instructions not to drive in the rain.
While I was down there, I noticed one more missing washer, which I fixed. That one was the front of the two back ones on the opposite side. Those have some top access, so I hosed it down liberally with PB blaster a few hours ahead of time. That went smoothly.
A test-drive confirmed that the car was much more responsive to steering input (it was getting horrible, I knew something was wrong). Too bad a .5 hour project turned into a 4-hour (approximate) project, but at least it'* safe again. I'm just thrilled that I caught it before the power met the pavement in a very literal sense. It'* disturbing that a reasonably rust-free (for Michigan) '96 had this problem though! I'm all paranoid now.
It should have been easy. It wasn't.
I went to a local junkyard and got a handful of the washers and bolts.
I came home and started to loosen the bolt with a breaker bar, and it started out alright. Then it got harder to turn, and with surprisingly little effort, it snapped right off.
Bummer.
And of course, the subframe mount in question is the one with no top access to the captive nut. It'* the rear-most one. Double-bummer.
So... I did what I had to do. It was either cut a hole in the inner fender, or the dead-pedal area of the floor. The floor won, since carpet hides ugly repairs better than undercoating.
To make the hole, I drilled a series of small holes very close to each other on three sides, and then punched through the remaining material with a flat blade screwdriver and hammer. Then I peeled it up like a sardine can (the sheet steel there is disturbingly thin).
From there I could see that my captive nut was held in place by a sheet metal cover of sorts, which was welded in place on two sides. Channeling my anger and frustration, I beat on it with screwdrivers, hammers, and punches until I'd cut it in half, so that I could then peel the two welded-on sides away from the nut assembly, and remove it. It'* a rather large, diamond-shaped metal plate attached to the bottom of the nut, for the record.
Reassembly went well. I was going to use a new nut and flat washers on the top side, but apparently Lowes, Home Despot, Napa, Autozone, and TSC don't think m12 x 1.75 class 10.9 nuts are an item they need to carry. I was pissed. But it motivated me to work harder to unstick the stock nut and bolt-fragment, which did work, after PB blaster, heat (repeat a few times), vise-grips, and more brute force. I am glad it worked that way, because the stock nut assembly was still large enough/bulky enough that it wouldn't turn in it'* place as I tightened it up. Score! It'* not exactly captive, it could be pushed out of the way accidentally, but if someone was careful, they could remove it and replace it again without re-opening my access hole.
Speaking of the access hole: I folded the metal back into place, and sprayed it up good with automotive primer. It looks okay, but I have a feeling there is still some exposed metal on the back side. Any suggestions for making the repair as rust-resistant as possible? I haven't fabricated a patch yet, but that is the plan. I'll just sheet-metal-screw it in place with some goop in between to seal it. I'm just concerned about water splashing up into there through the few little holes that do access that compartment from the bottom, and corroding my floor. I don't really have good access to coat the back of the repair with anything though... Any thoughts would be appreciated.
For now, it'* just folded back, with the carpet back over it, and my wife has strict instructions not to drive in the rain.
While I was down there, I noticed one more missing washer, which I fixed. That one was the front of the two back ones on the opposite side. Those have some top access, so I hosed it down liberally with PB blaster a few hours ahead of time. That went smoothly.
A test-drive confirmed that the car was much more responsive to steering input (it was getting horrible, I knew something was wrong). Too bad a .5 hour project turned into a 4-hour (approximate) project, but at least it'* safe again. I'm just thrilled that I caught it before the power met the pavement in a very literal sense. It'* disturbing that a reasonably rust-free (for Michigan) '96 had this problem though! I'm all paranoid now.
#6
I have the same isue happening on my 97 Buick lesabre custom. one of the rear washers on the passenger side toward the middle the washer is completely missing. found this out when i brought it to my buddy who is a mechanic and he put it up on the lift and realized it was only being held by the outer rear on the passenger side. there are four total in the rear and two in the front. i called the dealership and they want 30 for the lower bushing, 25 for the washer and $6 for the bolt just for one of each. i live up in boston area so we have snow but the car has under 73k on it and was owned by an older couple who drove it like older people do. I just got the car a couple days ago. So i am just thinking of replacing the one for now but the rest i know need to be redone. the bushings still look ok though. Any suggestions on if i should just do all 4 rears and does anyone know where i can buyt he whole kit other than the dealership?
#7
I peeked under the Le Sabre today, and got a bit of a shock. One of the really big curvy-stamped sub-frame mount washers was almost falling off! The bolt is still in there just fine. I don't have much rust under there. The washer is rusted right out though.
Anyone else have this happen?
Anyone else have this happen?
#8
Yeah, apparently this guy just had it happen to him. Read his and you'll want to fix it right away.
http://www.bonnevilleclub.com/forum/...130&highlight=
As far as I know, those are a dealer only item and not cheap.
http://www.bonnevilleclub.com/forum/...130&highlight=
As far as I know, those are a dealer only item and not cheap.
#9
It is not a dealer only fix it'* actually quite simple
#10
Senior Member
We would Please like to request that you not post to threads older than 6 months. Chances are that none of the above members are participating anymore.
Instead,create a new thread for further conversations in the appropriate section & feel free to place a link from this post.
For further information please see site rules & policy re Bumping Old Threads.https://www.gmforum.com/introduction...-first-304557/
Thread Closed.
Instead,create a new thread for further conversations in the appropriate section & feel free to place a link from this post.
For further information please see site rules & policy re Bumping Old Threads.https://www.gmforum.com/introduction...-first-304557/
Thread Closed.
__________________
1997 Buick Pk Ave (Soft Ride) Suspension!
1997 Buick Pk Ave (Soft Ride) Suspension!
The following users liked this post:
CathedralCub (10-17-2018)
Thread
Thread Starter
Forum
Replies
Last Post
crash93ssei
Performance, Brainstorming & Tuning
14
06-24-2007 01:57 PM