Remote Start
#1
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Aug 2009
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Remote Start
I bought an Aftermarket Generation remote start kit and i wanted to install it myself but there are so many wires and i dont want to mess anything up. I went to an installer and he said i need to buy a bypass kit because my car has a transponder key or something. I think he'* lying and i'd like to know what all do i need in order to put a remote start on my bonny. Its a 2000 bonneville se
#3
Retired
No, he wasn't lying. Your car has a anti theft feature. Wrong key, and you won't start. I believe you can bypass the VATS system, but I only see a Tech article for 92-99. Someone should chime in with more info.
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#4
-- SITE DONATOR --
True Car Nut
I have a remote start on my 03 SSEi. I have an autostart remote start, and we used a flash logic bypass module. You would need an FLDL1, and you also have to have a programmer to program it. If your going to have it installed, best to just let them use there module and take care of it all for you. They are costly, I think the FLDL1 is around 80-90 dollars. Expect the same pricing from them for the bypass module.
#6
Retired
Post a link for that item you have found. We should be able to tell you if it will work or not. IMO, I wouldn't trust some of the stuff on Ebay.
__________________
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
Retired Administrator
2002 *-10 5.7 V8
2023 Jeep Rubicon Diesel
#7
-- SITE DONATOR --
True Car Nut
If you have the shop install it, they likely will refuse to use any bypass module other than their own. We would never use anything but our own product as far as remote starts go, just because you would have to learn any new product you were installing which takes time, as well as you don't know the quality. It'* best to stick with something you know works.
If you plan on doing the install yourself, find something with a good set of instructions and reputation. I believe the 2003 is still on the CAN bus, which should make it easier to install a remote start with the proper bypass module and instructions, everything should be controlled through 1 wire. If I remember correctly, everything can also get destroyed through that 1 wire if you make a mistake though, mainly your PCM.
I didn't actually install my remote start, but I worked very closely with our installer on many of them and am trying to recall how it all goes. Like Mike said, post up what you found and someone should know something about it.
If you plan on doing the install yourself, find something with a good set of instructions and reputation. I believe the 2003 is still on the CAN bus, which should make it easier to install a remote start with the proper bypass module and instructions, everything should be controlled through 1 wire. If I remember correctly, everything can also get destroyed through that 1 wire if you make a mistake though, mainly your PCM.
I didn't actually install my remote start, but I worked very closely with our installer on many of them and am trying to recall how it all goes. Like Mike said, post up what you found and someone should know something about it.
#9
-- SITE DONATOR --
True Car Nut
If you go here http://www.flash-it.com/, you can enter your vehicle, it will show you the compatible flash logic modules for your car (FLDL1 is the cheapest that does everything you need) then look at the install guide. It is mostly wiring in-between the remote start module and the bypass module, very few of the cars wires get used. I have heard of XpressKit before, I believe we actually used them for a while as well, I'm not familiar with how they work but I would assume it'* about the same.
No matter what module you use: As a rule of thumb, I have found it is best to run a new fused posative line from the battery to the remote start, they tend to be picky about voltage. It is also best to solder all connections possible, using the wire taps and such generally comes back to bite you later when one comes loose.
No matter what module you use: As a rule of thumb, I have found it is best to run a new fused posative line from the battery to the remote start, they tend to be picky about voltage. It is also best to solder all connections possible, using the wire taps and such generally comes back to bite you later when one comes loose.