Supercharger Swap
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: Jun 2003
Location: Mid Missouri
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
Supercharger Swap
I don't me to sound uneducated, but what is the difference between the a 92-93 superchrger and a 94-95. Can they be swapped?
Thanks
BigT
Thanks
BigT
#2
Senior Member
True Car Nut
Join Date: May 2002
Location: Edmonton, AB Canada
Posts: 2,621
Likes: 0
Received 0 Likes
on
0 Posts
Re: Supercharger Swap
Originally Posted by bigtjohnson
I don't me to sound uneducated, but what is the difference between the a 92-93 superchrger and a 94-95. Can they be swapped?
Thanks
BigT
Thanks
BigT
#3
Member
Posts like a V-Tak
Thread Starter
Join Date: Jun 2003
Location: Mid Missouri
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
Pulley Size
the pulley sizes are also different
Thanks
BigT
#4
Pulley is smaller on the 93. as far as hp i have read that the 94-95 series1 has app 25 more hp than previous years. I thought the 94'* ran same amount of boost as the 93'* just with slower rotor speed but when I done swap my boost dropped I had to put 93(2.5)pulley back on to get back to 9lbs of boost.
#5
Junior Member
Posts like a Ricer Type-R
Join Date: Feb 2003
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
I done the swap,needs larger throttle body,E.G.R. tube larger,bolts to manifold longer,air intake hose to throttle body bigger use 95 hose to air box.my boost was 7# reinstalled 92/93 smaller pulley now 10# also get the MINI AFC 2 [111%SETTING] it'* worth doing and passes california smog.
#6
I did not realize there was a differance in 93 and 92'*. All I need was the 70mm tb and 95 Sc. Then the ZZp mini AFC2.0. My egr tube and everything else was direct fit.
On your mini AFC2.0 did you set it 111% all 13 settings???
Reason I ask mine ranges from 110% - 121% to WOT. I have seen where several Say theirs is set at a single giving percentage.
On your mini AFC2.0 did you set it 111% all 13 settings???
Reason I ask mine ranges from 110% - 121% to WOT. I have seen where several Say theirs is set at a single giving percentage.
#7
Junior Member
Posts like a Ricer Type-R
Join Date: Feb 2003
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
92 and 93 the same, the throttle bore increased to70-73mm in94/95 super charge series 1 E.G.R. TUBE needs to be adapted to larger size. I bored my92/93 E.G.R. body out to 94/95 size, that'* the way I did it.never tried using other setting, wished zoomer had better directions!!!!!!
#8
I had a 93 3800sc and had to do nothing but bolt the 95 Throttle body and sc on. I guess the EGR tube is differant from 92 and 93. Everything was a direct bolt on with no modifications.
#10
Guest
Posts: n/a
i did this swap last feb. plus i enhanced the airflow with a 2" overdrive pulley, a 3" intake tube, a 95 SC, 95 TB( both were ported and polished to match eachother, a hi flow cat and a flowmaster. with the enhanced airflow, i have my afc 2.0 setup in enhanced mode starting with a 126% from 1-5 and gets progressively richer from 6-13 up to a final seting at 13 of 136%. now that the temps are colder, i may go even richer at the top end of the scale because cold air is denser than warm air. as far as the egr tube to SC, i have to find another seal that fit it snuggly. it does take time to get the afc set correctly, depending on your mods, you may have different settings from others. airflow and air temp is the key.
also with overdriving a SC, since i havent seen an intercooler for a series 1 yet offered, you need to get the incoming air as cold as possible before it gets to the SC. i insulated my entire intake and built a cold air box. after doing this, my IAT temps dropped 40* you may also want to coat your manifolds too. im getting a set done by performance coatings in washington state. they do the inside and out of them. if your exhaust gas temps are 1590*, the radiant temp from you manifold is aprox 200* if they are uncoated. after the coating is applied, the radiant temp from the manifolds are 80*.
as a rule of thump, they state that for every 10* of engine bay temp that you reduce, you will gain aprox 1% HP gain.
so if you drop it 120* and you are making 300 HP at the flywheel, that is an aprox gain of 36 HP. not bad for the 190 bux they charge for the chromex finish, the satin finishes are 150 for the set .
also with overdriving a SC, since i havent seen an intercooler for a series 1 yet offered, you need to get the incoming air as cold as possible before it gets to the SC. i insulated my entire intake and built a cold air box. after doing this, my IAT temps dropped 40* you may also want to coat your manifolds too. im getting a set done by performance coatings in washington state. they do the inside and out of them. if your exhaust gas temps are 1590*, the radiant temp from you manifold is aprox 200* if they are uncoated. after the coating is applied, the radiant temp from the manifolds are 80*.
as a rule of thump, they state that for every 10* of engine bay temp that you reduce, you will gain aprox 1% HP gain.
so if you drop it 120* and you are making 300 HP at the flywheel, that is an aprox gain of 36 HP. not bad for the 190 bux they charge for the chromex finish, the satin finishes are 150 for the set .