Something else I noticed...
#1
Junior Member
Thread Starter
Join Date: Apr 2006
Location: Purgatory
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Something else I noticed...
My performance ride and touring ride lights are both lit up. But the traction, perf shif, and normal shift lights work fine. Also when I push the either of the ride buttons, I don't hear or feel anything.
EDIT - And, when I hit bumps, I get a ding ding ding sound
EDIT - And, when I hit bumps, I get a ding ding ding sound
#2
Junior Member
Posts like a Ricer Type-R
http://www.bonnevilleclub.com/forum/...e=article&k=27
I believe your ding ding problem is unrelated. It may be a flaky trunk or hood switch thinking you have something open, or it may be a master cylinder issue that is made worse by bumps. Keep a close eye on that one.
After you find out how much CCR struts are to replace (after reading the above link), go here:
http://www.williamwren.com/struts/elc.html to the bottom of the page to learn how to disable the system and go with conventional struts.
I believe your ding ding problem is unrelated. It may be a flaky trunk or hood switch thinking you have something open, or it may be a master cylinder issue that is made worse by bumps. Keep a close eye on that one.
After you find out how much CCR struts are to replace (after reading the above link), go here:
http://www.williamwren.com/struts/elc.html to the bottom of the page to learn how to disable the system and go with conventional struts.
#4
Junior Member
Thread Starter
Join Date: Apr 2006
Location: Purgatory
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Well, I'm convinced the CCR is fried. I ran the codes and got 12, 23, 24, 25, 26, 33, 12. Where is the CCR? markviisvt4 I believe gave me a used CCR that works.
#5
Senior Member
Certified Car Nut
Join Date: Oct 2003
Posts: 19,756
Likes: 0
Received 0 Likes
on
0 Posts
http://www.bonnevilleclub.com/forum/...&highlight=ccr
Codes
Code 23 = LF actuator position error
Code 24 = RF actuator position error
Code 25 = LR actuator position error
Code 26 = RR actuator position error
Code 31 = lift/dive signal error
Code 32 = lateral acceleration switch input error
Code 33 = driver select switch error
Code 34 = vehicle speed signal error
Codes
Code 23 = LF actuator position error
Code 24 = RF actuator position error
Code 25 = LR actuator position error
Code 26 = RR actuator position error
Code 31 = lift/dive signal error
Code 32 = lateral acceleration switch input error
Code 33 = driver select switch error
Code 34 = vehicle speed signal error
#7
Junior Member
Posts like a Ricer Type-R
The module is under the driver'* seat. It as a 32-pin connector. Please check to be sure you have 12V at pin C16 (brown wire) with ignition on.
Your struts should be 20-60 ohms when checked across these pins:
LF D13 to D10
RF C13 to C10
LR D14 to D11
RR C14 to D9
But just because the resistance is good on each strut does NOT mean the strut is good.
With all the codes you have, I suspect a module, but wouldn't be surprised to see a bad strut or two ALSO.
Your struts should be 20-60 ohms when checked across these pins:
LF D13 to D10
RF C13 to C10
LR D14 to D11
RR C14 to D9
But just because the resistance is good on each strut does NOT mean the strut is good.
With all the codes you have, I suspect a module, but wouldn't be surprised to see a bad strut or two ALSO.