91 Le Sabre brake drum stuck on the shoes
#1
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Sep 2005
Location: Budd Lake, NJ
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
91 Le Sabre brake drum stuck on the shoes
I managed to pull the passenger side drum by prying it hard against the backing plate, and it finally slid off due to the ruptured wheel cylinder and brake lube (er, fluid) all over the place.
The driver'* side is hung up on the shoes. It comes about 3/4" off, then the groove is hanging up on the shoes. The adjuster is no help, neither is slacking off the parking brake cable. On this car, I can't reach the adjuster starwheel from the access hole. I know, since I had the other side apart.
Any suggestions besides just hitting the drum with a bigger hammer? I got as far as I can with the screwdrivers to pry with.
Thanks!
The driver'* side is hung up on the shoes. It comes about 3/4" off, then the groove is hanging up on the shoes. The adjuster is no help, neither is slacking off the parking brake cable. On this car, I can't reach the adjuster starwheel from the access hole. I know, since I had the other side apart.
Any suggestions besides just hitting the drum with a bigger hammer? I got as far as I can with the screwdrivers to pry with.
Thanks!
#2
Senior Member
True Car Nut
Well, geez, you should be able to back off the adjuster through the hole. That'* what the durned thing is there for! You know you've got to hold out the little pawl that keeps the star wheel from turning backwards, while you spin the wheel, right?
Anyways, if that ain't doin' it for you, here is an idea (I have never done this, so.....) grind off the heads of the nails on the backing plate that hold the shoes in place with the spring and cup on the front side, or clip the heads off if you can get a pair of side cutters under the head. May be tough to do since the nails are under spring pressure. This might allow the shoes to move enough to get the drum off?
If it still won't come, get you a big 'ol grinder with a cut-off wheel. (Rent one if you don't own one or buy one at Harbor Freight for $15) and cut the drum through the edge to the middle. It'll come off then, by George! Then go to your local junkyard and get another one.
You may want to wait to see if some smarter person has a less barbaric approach.
Anyways, if that ain't doin' it for you, here is an idea (I have never done this, so.....) grind off the heads of the nails on the backing plate that hold the shoes in place with the spring and cup on the front side, or clip the heads off if you can get a pair of side cutters under the head. May be tough to do since the nails are under spring pressure. This might allow the shoes to move enough to get the drum off?
If it still won't come, get you a big 'ol grinder with a cut-off wheel. (Rent one if you don't own one or buy one at Harbor Freight for $15) and cut the drum through the edge to the middle. It'll come off then, by George! Then go to your local junkyard and get another one.
You may want to wait to see if some smarter person has a less barbaric approach.
#3
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Sep 2005
Location: Budd Lake, NJ
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
I got it off!
It wasn't as bad as I thought, I just needed more tool!
Two small wrecking bars worked wonders together. The drum came of with only moderate effort once I got the prisers of both bars behind the drum, I levered them in opposite directions and the drum slid right off.
It turns out that the groove wasn't as bad in this drum, but the wheel cylinder was just as bad!
I hope this tip helps someone else get their sticky drums off!
BTW, to reply to Bill, this is the type of drum brake without retainer springs! It has the big U shaped spring that holds the shoes to the backing plate, and also holds retracts them. I'd never seen one like it until I pulled the drum off the other side, and was really worried that it would be a big deal to replace the shoes. Actually, this setup is easier than drum brakes with the retainer springs.
Thanks for the help!
Two small wrecking bars worked wonders together. The drum came of with only moderate effort once I got the prisers of both bars behind the drum, I levered them in opposite directions and the drum slid right off.
It turns out that the groove wasn't as bad in this drum, but the wheel cylinder was just as bad!
I hope this tip helps someone else get their sticky drums off!
BTW, to reply to Bill, this is the type of drum brake without retainer springs! It has the big U shaped spring that holds the shoes to the backing plate, and also holds retracts them. I'd never seen one like it until I pulled the drum off the other side, and was really worried that it would be a big deal to replace the shoes. Actually, this setup is easier than drum brakes with the retainer springs.
Thanks for the help!
#4
Senior Member
True Car Nut
Re: I got it off!
Originally Posted by PaulDFixr
It wasn't as bad as I thought, I just needed more tool!
BTW, to reply to Bill, this is the type of drum brake without retainer springs! It has the big U shaped spring that holds the shoes to the backing plate, and also holds retracts them. I'd never seen one like it until I pulled the drum off the other side, and was really worried that it would be a big deal to replace the shoes. Actually, this setup is easier than drum brakes with the retainer springs.
Thanks for the help!
BTW, to reply to Bill, this is the type of drum brake without retainer springs! It has the big U shaped spring that holds the shoes to the backing plate, and also holds retracts them. I'd never seen one like it until I pulled the drum off the other side, and was really worried that it would be a big deal to replace the shoes. Actually, this setup is easier than drum brakes with the retainer springs.
Thanks for the help!
If I had thought of it earlier, lots of rental shops rent really big pullers that you can use to pop off a stubborn drum.
Anyway, glad you got it off!
#5
Senior Member
Posts like a Northstar
Join Date: Dec 2005
Location: Indianapolis
Posts: 560
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by bill buttermore
You may want to wait to see if some smarter person has a less barbaric approach.
Do the back wheels even turn when the car is on the ground and in drive? If so, then the brakes are not welded.
#6
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Sep 2005
Location: Budd Lake, NJ
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by impatient99
Originally Posted by bill buttermore
You may want to wait to see if some smarter person has a less barbaric approach.
Do the back wheels even turn when the car is on the ground and in drive? If so, then the brakes are not welded.
Thanks!
Thread
Thread Starter
Forum
Replies
Last Post