Will this amp fit my Alt?
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: Nov 2008
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
Will this amp fit my Alt?
Hello Bonnie GuRu'*,
Will this Amp http://www.sonicelectronix.com/item_...00.5.html#tabs Fit my Alt?
How much is the Alt Amp Output? I read its 105A. This is a 1300w amp 4.1 speaker output.
I did replace the HU with a AMR and did buy the PAC Harness. http://www.sonicelectronix.com/item_...C2R-GM32R.htmlTHe install was a breeze IF you unlatched the two (2) plastic hold pins on your upper gauges.
I have a Kenwood HU
Infinity'* all round
12" Sub pushed by 180w at the moment.
Yes the speakers were a "female dog" to install. I rather suck on my toes next time.
Let me know if I have your folks blessing on this all-in-one 1300w amp.
Thanx!
Viper
Will this Amp http://www.sonicelectronix.com/item_...00.5.html#tabs Fit my Alt?
How much is the Alt Amp Output? I read its 105A. This is a 1300w amp 4.1 speaker output.
I did replace the HU with a AMR and did buy the PAC Harness. http://www.sonicelectronix.com/item_...C2R-GM32R.htmlTHe install was a breeze IF you unlatched the two (2) plastic hold pins on your upper gauges.
I have a Kenwood HU
Infinity'* all round
12" Sub pushed by 180w at the moment.
Yes the speakers were a "female dog" to install. I rather suck on my toes next time.
Let me know if I have your folks blessing on this all-in-one 1300w amp.
Thanx!
Viper
#2
Senior Member
Posts like a Corvette
Join Date: Jun 2008
Location: Cleveland, OH
Posts: 1,389
Likes: 0
Received 0 Likes
on
0 Posts
you only push 180 watts to that sub? can you hear it lol
I run a 1200 watt Kenwood with just a little dimming but I ran heavier wire from the alt to the front fuse block then heaverier wires from the battery positive to the rear fuse block since thats where my amp is connected
without a cap there is some dimming at idle but other than that everything is fine
I run a 1200 watt Kenwood with just a little dimming but I ran heavier wire from the alt to the front fuse block then heaverier wires from the battery positive to the rear fuse block since thats where my amp is connected
without a cap there is some dimming at idle but other than that everything is fine
#3
Senior Member
Posts like a Turbo
Join Date: Jan 2008
Location: rockford, illinois
Posts: 281
Likes: 0
Received 0 Likes
on
0 Posts
Well crunch amps are not CEA certified so it will do a little bit less than what they advertise it at. It only has 1 70 amp fuse on it so you alternator should handle it.
#4
Member
Posts like a V-Tak
Thread Starter
Join Date: Nov 2008
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
Correction. I misstated the watt usage on the 12" sub. The correct amount in 180 RMS output @ 4 ohms.
Also. If the lights are dimming, that means you are putting to much stress on your alt.
Also. If the lights are dimming, that means you are putting to much stress on your alt.
#5
Senior Member
Posts like a Corvette
Join Date: Jun 2008
Location: Cleveland, OH
Posts: 1,389
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
92buickregalgransp
Buick
4
02-09-2014 08:22 AM
Paulnold
Performance, Brainstorming & Tuning
9
05-04-2004 12:36 PM