wattage nd clipping
#11
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2010
Location: kentucky
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
so is that why my amp is clipping becaouse its too weak
like my subs are pulling too much from the amp ??????? and they both are 4 ohm subs wired parellel to 2 ohm
like my subs are pulling too much from the amp ??????? and they both are 4 ohm subs wired parellel to 2 ohm
#12
Senior Member
True Car Nut
Join Date: Jun 2007
Location: New Lenox, IL
Posts: 2,478
Likes: 0
Received 0 Likes
on
0 Posts
#13
Senior Member
True Car Nut
Join Date: Mar 2010
Location: Eaton Rapids MI
Posts: 2,964
Likes: 0
Received 0 Likes
on
0 Posts
subs dont "pull power" from amps, fyi. But yes ur amp is not powerful enough and u had ur subs wired to 1 ohm, and ur amp is not 1 ohm stable
#14
Senior Member
Posts like a Turbo
Join Date: Jul 2010
Location: Sacramento, CA.
Posts: 326
Likes: 0
Received 0 Likes
on
0 Posts
ok i have an alpine type r 12 and a type r 10 i have an infinity refrence 611a mono block amplifier the specs on the amp say 676 watts rms at 2 ohms but my subs will hold at least 400 a piece rms and when i turn my amps gain up halfway the clip light starts flashing bassboost is all the way down and no bass on my head unit will i blow my subs if i turn it more or should i back down
But your clip light is flashing because you're clipping the signal
The gain on your amp is not supposed to be used a volume ****, it'* to allow you to match the input signal from your deck to the amp so they're "on the same page" so to speak. There are several ways to set the gain, the best being with the help of an oscilliscope. But not many people have one and even fewer actually know how to use them so that means you either have to do it by ear or use a dmm and this chart to get it dialed in
Yes, sending clipped signal to your subs can and will result in blown subs
The subs dictate how much power the amps put out based on the impedance of said subs. If his subs were wired at too low of an impedance for his amp that wouldn't cause clipping, that would cause his amp to go into protect. Clipping is caused when the amp attempts to deliver an output signal that exceeds it'* capability, i.e., turning the gain too high.
#15
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2010
Location: kentucky
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
ok i did the test on the chart and when i set my gain on the amp its at 40 volts with no clip light is that ok ??????? and when i turned the gain all the way up it read like 53.3 is that normal for a 676 rms amp or is this amp more powerful than infinity gives it credit for ???also im getting 14 volts dc at the power wire on amp
#16
Senior Member
Posts like a Turbo
Join Date: Jul 2010
Location: Sacramento, CA.
Posts: 326
Likes: 0
Received 0 Likes
on
0 Posts
ok i did the test on the chart and when i set my gain on the amp its at 40 volts with no clip light is that ok ??????? and when i turned the gain all the way up it read like 53.3 is that normal for a 676 rms amp or is this amp more powerful than infinity gives it credit for ???also im getting 14 volts dc at the power wire on amp
There is no "normal" for any amp cause what you're doing is matching the signal from the deck to your amp. So if you had two decks, one with 2v preouts and one with 8v preouts and connected them to your existing amp, the gain setting would be different for both of them because the preout voltage is different. Does that make sense? I'm not exactly the best at explaining things
#17
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2010
Location: kentucky
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
yes that does make sense and thanx for the input (ha ha) lil dry humor but i do appreciate it im tryin to get my hands on another amp one for each sub and it sounds way better with both subs the 10 has better response than the 12 they both sound awesome together i dont think it will mess anything up having a 10 and a 12 theyre both 4 ohm subs wired paralell to 2 ohm and they both have the same rmsand what not in seperate boxes
#18
Senior Member
Posts like a Turbo
Join Date: Jul 2010
Location: Sacramento, CA.
Posts: 326
Likes: 0
Received 0 Likes
on
0 Posts
yes that does make sense and thanx for the input (ha ha) lil dry humor but i do appreciate it im tryin to get my hands on another amp one for each sub and it sounds way better with both subs the 10 has better response than the 12 they both sound awesome together i dont think it will mess anything up having a 10 and a 12 theyre both 4 ohm subs wired paralell to 2 ohm and they both have the same rmsand what not in seperate boxes
One thing to remember though is that when you connect the subs to the amp, those two 2ohm loads become one 1ohm load and I don't think your amp is stable down to 1ohm so while it might work for a while, you're definitely on borrowed time.
#19
Senior Member
Posts like a Turbo
Join Date: Jul 2010
Location: Sacramento, CA.
Posts: 326
Likes: 0
Received 0 Likes
on
0 Posts
When you have two DVC 4 ohm subs, the final impedances you can end up with when hooked up to a mono amp are 16, 4, 1.......and of course 16 should never ever be considered as an option so let'* keep it real, it'* 4 and 1.
#20
Member
Posts like a V-Tak
Thread Starter
Join Date: Mar 2010
Location: kentucky
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
so if i wired the subs individually in each box with one voice coil 4 0hm and then put them on seperate channels it would be a 2 ohm load on the amp ???