wire identification
#1
Senior Member
Posts like a 4 Banger
Thread Starter
Join Date: Jun 2005
Location: washington
Posts: 111
Likes: 0
Received 0 Likes
on
0 Posts
wire identification
can anyone identify the wires going into the rear amplifier on my 2000 ssei? As far as postive, negative, left, right, front, rear?
#3
Senior Member
True Car Nut
Join Date: Oct 2002
Location: Groton, CT _NEBF 05, 06, 07_
Posts: 2,703
Likes: 0
Received 0 Likes
on
0 Posts
Positive supply (+12vdc) to rear amplifier - C2 H Positive & C2 A Negative
Speakers LF Door - C1 A11 (-) & A12 (+)
Speakers RF Door - C1 A7 (-) & A8 (+)
Speaker LR Door - C2 B (-) & G (+)
Speaker LR (subwoofer) - C2 F (-) & C (+)
Spoeaker RR Door - C1 A10 (-) & A9 (+)
Speaker RR (subwoofer) C2 E (-) & D (+)
Hope this info helps a little.
Speakers LF Door - C1 A11 (-) & A12 (+)
Speakers RF Door - C1 A7 (-) & A8 (+)
Speaker LR Door - C2 B (-) & G (+)
Speaker LR (subwoofer) - C2 F (-) & C (+)
Spoeaker RR Door - C1 A10 (-) & A9 (+)
Speaker RR (subwoofer) C2 E (-) & D (+)
Hope this info helps a little.
#4
Senior Member
Posts like a 4 Banger
Professor---
I've the complete diagrams in pdf including
the infamous radio pinout I've just verified
against my 2000 -
Rear amp integration unit
charging system
With & without amp
etc....
Need someplace to send it !
but am finishing up the doc'* to the install
By the way there should be a switched 12v
at your radio 3rd pin from right bottom row
verify this to be ign hot? Mine is not but I
have a non amp'd system and it only shows
on the diagram with the amplified system...
Also hit the wire that failed to have 12v switched
on it (yellow switched 12v on your gm07b adapter)
with the antenna enable wire from your new head
it powers the antenna booster...
__________________________
Just read your previous post
Press UP on the center of the two plastic rivets above the guage cluster
remove said rivets
remove pocket/panel lower left steering column
grasp facia above air control cluster
pry up
unplug the tire pressure cluster
remove by rotating counter clockwise over steering wheel
careful of the steering tilt armature
Press in 4 metal tabs to release the head unit
You'r just about a week too quick for me
if I can get the time to do the SWI-X this weekend
and finish up the docs for this procedure.....
I've the complete diagrams in pdf including
the infamous radio pinout I've just verified
against my 2000 -
Rear amp integration unit
charging system
With & without amp
etc....
Need someplace to send it !
but am finishing up the doc'* to the install
By the way there should be a switched 12v
at your radio 3rd pin from right bottom row
verify this to be ign hot? Mine is not but I
have a non amp'd system and it only shows
on the diagram with the amplified system...
Also hit the wire that failed to have 12v switched
on it (yellow switched 12v on your gm07b adapter)
with the antenna enable wire from your new head
it powers the antenna booster...
__________________________
Just read your previous post
Press UP on the center of the two plastic rivets above the guage cluster
remove said rivets
remove pocket/panel lower left steering column
grasp facia above air control cluster
pry up
unplug the tire pressure cluster
remove by rotating counter clockwise over steering wheel
careful of the steering tilt armature
Press in 4 metal tabs to release the head unit
You'r just about a week too quick for me
if I can get the time to do the SWI-X this weekend
and finish up the docs for this procedure.....
Thread
Thread Starter
Forum
Replies
Last Post
Peterg22000
Detailing & Appearance
16
07-08-2006 02:55 PM
2000SilverBullet
Your Ride: GM Pictures & Videos
24
12-01-2005 11:13 PM