GM Forum - Buick, Cadillac, Olds, GMC & Pontiac chat

GM Forum - Buick, Cadillac, Olds, GMC & Pontiac chat (https://www.gmforum.com/)
-   2000-2005 (https://www.gmforum.com/2000-2005-90/)
-   -   Question about antifreeze flushing? Which heater hose? (https://www.gmforum.com/2000-2005-90/question-about-antifreeze-flushing-heater-hose-253827/)

BADLEG 03-19-2007 08:20 AM

Question about antifreeze flushing? Which heater hose?
 
Does anybody know which hose Im supposed to cut in the t valve to flush out the old dexcool? There is a large hose (feeding?) the heater core and a smaller one returning to the engine. I would have thought to backflush I should install the t in the small return line? Anybody know for sure?

BillBoost37 03-19-2007 08:37 AM

You could use either heater hose. However to help bleed air in the future, I'd suggest the higher of the two if one is higher than the other.

BADLEG 03-19-2007 08:43 AM


Originally Posted by BillBoost37
You could use either heater hose. However to help bleed air in the future, I'd suggest the higher of the two if one is higher than the other.

Wouldnt it be more productive for flushing to reverse the flow in the heater core and the engine. As opposed to the way it normally flows when being pumped by the water pump?

toastedoats 03-19-2007 08:45 AM


Originally Posted by BADLEG

Originally Posted by BillBoost37
You could use either heater hose. However to help bleed air in the future, I'd suggest the higher of the two if one is higher than the other.

Wouldnt it be more productive for flushing to reverse the flow in the heater core and the engine. As opposed to the way it normally flows when being pumped by the water pump?

yes, however, when installing a "T" your not actually forcing water in one certain direction....

i think... its early.... and its monday

BillBoost37 03-19-2007 08:53 AM

No, by adding a T, you are forcing water in both directions aka T ;)

If you want to do it my way, skip the T, unhook the heater hoses and flush the block through each hose inlet back to the radiator, then from the radiator back, and through the waterneck, and flush the heater core seperately...both directions on easy and every way you can.

That's a full flushing.

Archon 03-19-2007 10:13 AM

IIRC, if you purchase the Prestone Flush Kit, the instructions say to put it in the inlet heater hose, without an explanation as to why.

BillBoost37 03-19-2007 11:25 AM


Originally Posted by Archon
IIRC, if you purchase the Prestone Flush Kit, the instructions say to put it in the inlet heater hose, without an explanation as to why.

Dick...got the inlet identified? I forget if it's the top or bottom on your year. ;)

Archon 03-19-2007 12:10 PM

Thanks for the gentle nudge, Bill. That would have been useful information to provide. :oops: The top hose is the inlet.

BADLEG 03-19-2007 01:35 PM

Would the Larger diameter hose always be the inlet or the the one feeding the heater core?

Archon 03-19-2007 02:16 PM

Like "never say never", also "never say always". ;-) For instance, some vehicles have the same size in and out. In this particular case, the coolant comes out of the top of the tensioner from the outlet closest to the alternator, runs through the heater hose (which in this case is the larger of the two hoses), through the heater core, back out through the other heater hose and back to the tensioner on the inlet that is closest to the firewall.


All times are GMT -4. The time now is 06:07 PM.


© 2024 MH Sub I, LLC dba Internet Brands