rotors constantly warping
#1
Senior Member
Posts like a Supercharger
Thread Starter
Join Date: Feb 2004
Location: Mashpee, MA
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
rotors constantly warping
HELP! My rotors on my car suck. I had them replaced right when i bought the car because they were obviously warped on the test drive. New ones put on @ 32,000. Those went at about 47,000 so i replaced them with ones from NAPA (we have an account there so they are @ cost). Now i'm at 61,000 and they are warped again! Any suggestion?!? It'* really noticeable at highway speeds when i apply the brakes. The steering wheel shakes uncontrolably and the brake pedal pulses like crazy. It seems to be a problem only with the front rotors, I haven't had a problem with the rear ones, though i have also replaced those as well. I would love to get this problem fixed!
#2
Senior Member
True Car Nut
Join Date: Jun 2003
Location: Purgatory
Posts: 6,313
Likes: 0
Received 0 Likes
on
0 Posts
Ty at www.domesticperformance.com can help out with slotted rotors. Several memebers here have them and are happy with the reliability.
#3
Senior Member
Posts like a Corvette
Join Date: Oct 2002
Location: New Jersey - Most of Our Elected Officials Have Not Been Indicted
Posts: 1,483
Likes: 0
Received 2 Likes
on
2 Posts
The next time you have the calipers off to replace the rotors(and possibly the pads) make SURE the piston and the slides in the calipers are moving freely.
#4
Senior Member
True Car Nut
Join Date: Jul 2003
Location: Westerville, Ohio 2000 Black SSEi
Posts: 6,127
Likes: 0
Received 1 Like
on
1 Post
Replace the rear pads and rotors. Kendra'* car was fine after i put the slotted rotors on to fix the same problem. She panic braked the car a few times and the problem came back. I figured it was the front rotors again so i swapped them to my car but no problems. Replaced the back rotors and pads on her car and the problem is gone. The back brakes are going to give you the bumpy (and low pressure in her case) pedal feel more so than the fronts.
The problem comes from the rear rotors being solid. It only takes a few panic brakes to warp them out pretty good even though they are only doing 30 percent of the braking.
The problem comes from the rear rotors being solid. It only takes a few panic brakes to warp them out pretty good even though they are only doing 30 percent of the braking.
#6
Senior Member
Posts like a Supercharger
Thread Starter
Join Date: Feb 2004
Location: Mashpee, MA
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
When i replaced the rotors the first time I did make sure the calipers where retracting freely. The front ones were fine, the back right was a little bit hard, but no problems with it the next time that I did them. I did read somewhere that you should use a torque wrench to put the wheels back on, and i did do that to try and avoid any possiblity of them warping. I may take the fronts off and have them turned, not sure what to do with the backs, i only replaced them 5k ago? Oh well between that and the motor mount it will be a long weekend! Installed the new lights, gonna test them out tonight.
#7
Senior Member
Posts like a Turbo
Join Date: Jan 2004
Location: Lake Forest, CA
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
I had an even worse experience with the stock rotors. I had to have them 2 times. I am now on my third set, but I purchased some other rotors this last time and they are great.
Stock rotors really do suck. They are only a single disk, not vented, cross-drilled, and not slotted. Check out the following link below as to where I got mine. Great Deal and I really put them through the paces.
http://www.nationalfleetparts.com/sp_performance.asp
Stock rotors really do suck. They are only a single disk, not vented, cross-drilled, and not slotted. Check out the following link below as to where I got mine. Great Deal and I really put them through the paces.
http://www.nationalfleetparts.com/sp_performance.asp
#8
Senior Member
Posts like a Northstar
Join Date: Dec 2002
Location: Bellbrook, Ohio
Posts: 547
Likes: 0
Received 0 Likes
on
0 Posts
I agree with willwren. If you have alum rims make sure you torque to 100 ft. pounds in the correct torque sequence. If you don't, new rotors will warp in short order. Also, if you are harder than normoal on your stops you should go with race-type slotted rotors or you will soon be in the same boat.
Thread
Thread Starter
Forum
Replies
Last Post