Question about Wheel Bearing Hub - driving on a bad one
#1
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Oct 2009
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Question about Wheel Bearing Hub - driving on a bad one
Thanks to you fine folks on this forum, I've determined the 2 remaining problems with my Bonneville I've owned for about a month. I've got the intermediate steering problem and I have a bad wheel bearing hub.
I've found a replacement wheel bearing hub for about $160 online, or around $200 from a place I've actually heard of. But I don't really have the money for this right now, as I spent most of my wad on this amazingly awesome car!
So my questions are:
Can I drive on a bad bearing hub? It'* only groaning if I turn to the left at a certain angle. It seems to be the rear driver'* side hub based on where the sound is coming from. I can't really afford to get it fixed today, so I was wondering how dangerous it was to the car to drive on it?
How hard is it really to change out the bearing hub? I've not been able to find a guide to doing it here or online, and yes I've searched a bit, unless I'm just blind which is ENTIRELY likely.
Thanks for any assistance you all can provide!
I've found a replacement wheel bearing hub for about $160 online, or around $200 from a place I've actually heard of. But I don't really have the money for this right now, as I spent most of my wad on this amazingly awesome car!
So my questions are:
Can I drive on a bad bearing hub? It'* only groaning if I turn to the left at a certain angle. It seems to be the rear driver'* side hub based on where the sound is coming from. I can't really afford to get it fixed today, so I was wondering how dangerous it was to the car to drive on it?
How hard is it really to change out the bearing hub? I've not been able to find a guide to doing it here or online, and yes I've searched a bit, unless I'm just blind which is ENTIRELY likely.
Thanks for any assistance you all can provide!
#2
Senior Member
True Car Nut
Changing the hub is not a bad task at all. The worse time you will have is breaking loose the nuts and bolts. But, some Liquid Wrench left to soak on them overnight should make it a much easier task.
I would not go too awfully long on driving with a bad bearing. But, if you drive easy and not do any high speed rapid lane changes or skidding corners, you can hold off. I would recommend if you are going to do one on the front or back that you do the opposite one as well.
Check out Rock Auto on their prices. RockAuto Parts Catalog
I would not go too awfully long on driving with a bad bearing. But, if you drive easy and not do any high speed rapid lane changes or skidding corners, you can hold off. I would recommend if you are going to do one on the front or back that you do the opposite one as well.
Check out Rock Auto on their prices. RockAuto Parts Catalog
#3
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Oct 2009
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Awesome, thank you. The used dealership I purchased it at has been pretty helpful with repairs so far and isn't charging me labor at all, so I may see if they will do it.
I can't wait to get this girl into top operating condition.
Luckily, I am just driving it to work and back right now. 7 miles each way on easy streets, but I want to drive it a little faster, I'm just waiting to make sure I have all the kinks worked out first
I can't wait to get this girl into top operating condition.
Luckily, I am just driving it to work and back right now. 7 miles each way on easy streets, but I want to drive it a little faster, I'm just waiting to make sure I have all the kinks worked out first
#4
Junior Member
Posts like a Ricer Type-R
Join Date: Oct 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Changing the hub is not a bad task at all. The worse time you will have is breaking loose the nuts and bolts. But, some Liquid Wrench left to soak on them overnight should make it a much easier task.
I would not go too awfully long on driving with a bad bearing. But, if you drive easy and not do any high speed rapid lane changes or skidding corners, you can hold off. I would recommend if you are going to do one on the front or back that you do the opposite one as well.
Check out Rock Auto on their prices. RockAuto Parts Catalog
I would not go too awfully long on driving with a bad bearing. But, if you drive easy and not do any high speed rapid lane changes or skidding corners, you can hold off. I would recommend if you are going to do one on the front or back that you do the opposite one as well.
Check out Rock Auto on their prices. RockAuto Parts Catalog
I would dis-agree with the statement that you need to do the opposite tire as well. Just because one of the bearings failed, does NOT mean the other is even close to failing. Bearings usually fail from contamination, lack of lube, or an "event". Chances of seals failing at the same time on two different wheels is slim to none...and that would be the contamination or lack of lube issue. An event could be a curb strike, or other such happening...also usually does NOT include both wheels. I would only replace the troubled wheel. The wheel bearing opposite my bad one in my Saturn was clean and tight.
I worked for Timken bearings for 4 years as an engineer - that is where my expertise comes from.
Good luck! Its not a hard job, but if the dealership is offering free service, I would take them up on it. Without an impact gun, it can be a tough job to get some of the bolts off. Also, if I remember right, you have to press the bearing assembly out of the mounting.
Hope that helps!
DH
#5
Senior Member
True Car Nut
I agree that both would not be recommended for replacement if one side did suffer from an 'event'.
On FWD vehicle, you'll seldom find a mechanic worth his grain in salt not recommend that both front hub/bearings be replaced. Especially if one side has worn so bad that slop is noticeable or the races have been distorted.
On 4X4'*, tires, bearings and brakes should always be done in pairs on the same axle. Especially in newer vehicles with tighter tolerances.
Hope this clears things up.
#6
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Oct 2009
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the info.
If they decide not to help me, apparently one of my good friends owns an impact wrench. He just let me know after I was telling him about the bearing hub. I was all "WHUT!" lol
Is this the right hub? The site seems to indicate that it is. (Interestingly enough, this site sells Timken bearings.)
wheelbearings.us
I guess it'* only $126. That'* pretty awesome.
What is involved in "pressing" the bearing out of the mounting? How reliable are Timken bearings? I'm pretty new to the "used car" scene, so I'm trying to squeeze every ounce of info out of it. lol
If they decide not to help me, apparently one of my good friends owns an impact wrench. He just let me know after I was telling him about the bearing hub. I was all "WHUT!" lol
Is this the right hub? The site seems to indicate that it is. (Interestingly enough, this site sells Timken bearings.)
wheelbearings.us
I guess it'* only $126. That'* pretty awesome.
What is involved in "pressing" the bearing out of the mounting? How reliable are Timken bearings? I'm pretty new to the "used car" scene, so I'm trying to squeeze every ounce of info out of it. lol
#9
Senior Member
Posts like a Supercharger
Join Date: Feb 2009
Location: Chicago, IL
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
Ill save you some money
I just put these on my 03
2003 03 Pontiac Bonneville Front Wheel Hub Bearings NEW:eBay Motors (item 110440991128 end time Oct-31-09 11:03:32 PDT)
I just put these on my 03
2003 03 Pontiac Bonneville Front Wheel Hub Bearings NEW:eBay Motors (item 110440991128 end time Oct-31-09 11:03:32 PDT)
#10
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Oct 2009
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, but I actually need the rear wheel ones. I did use that link to find them with the same seller though and they'll be far cheaper than what I originally thought. So I'm going to order them tomorrow.
I appreciate your help everyone
Edit:
Are the ones from AM autoparts going to be the same quality as the Timken ones? Or are they pretty much going to be 6 of one, half a dozen of the other?
I appreciate your help everyone
Edit:
Are the ones from AM autoparts going to be the same quality as the Timken ones? Or are they pretty much going to be 6 of one, half a dozen of the other?
Last edited by RetroPengo; 10-22-2009 at 09:59 AM.