Water in tail lights
#1
Senior Member
Posts like a Northstar
Thread Starter
Join Date: Dec 2006
Location: Niagara Region, ON, Canada
Posts: 635
Likes: 0
Received 0 Likes
on
0 Posts
Water in tail lights
Hi folks,
After changing my rear turn signal bulb, I discovered ice inside the tail light.
Not sure how water is leaking in there.
The housings and lenses are not cracked, fit seems nice and tight.
This is on both sides, because I changed both bulbs.
The ice is melted where the bulbs would be, obviously because of the heat of the bulb.
Any idea how to fix this? Take them off and silicone?
Not really a big deal right now, but I don't want it to turn into something worse!
(I didn't know if I should have posted in "electrical". There are no electrical malfunctions, so it was sort of a grey area)
As always, your advice is appreciated.
Thanks,
Adam
After changing my rear turn signal bulb, I discovered ice inside the tail light.
Not sure how water is leaking in there.
The housings and lenses are not cracked, fit seems nice and tight.
This is on both sides, because I changed both bulbs.
The ice is melted where the bulbs would be, obviously because of the heat of the bulb.
Any idea how to fix this? Take them off and silicone?
Not really a big deal right now, but I don't want it to turn into something worse!
(I didn't know if I should have posted in "electrical". There are no electrical malfunctions, so it was sort of a grey area)
As always, your advice is appreciated.
Thanks,
Adam
#3
Senior Member
Certified Car Nut
Join Date: Oct 2002
Posts: 11,308
Likes: 0
Received 0 Likes
on
0 Posts
My taillights are not cracked either, but one always fills up with water. I'd definitely check the seal all the way around. Maybe even check the rubber gaskets on the bulb housings?
#4
Member
Posts like a V-Tak
Join Date: Feb 2003
Location: Hobart, Indiana
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
I had this problem..
Fixed it by removing each taillight,
Siliconed around the gasket area,
bolt them back in.
Dry as a bone for about 6 months now!!!
You might also want to check the housings for cracks as well. Shopping carts like to crack 'em.
Good Luck!!
Bob
Fixed it by removing each taillight,
Siliconed around the gasket area,
bolt them back in.
Dry as a bone for about 6 months now!!!
You might also want to check the housings for cracks as well. Shopping carts like to crack 'em.
Good Luck!!
Bob
#5
Senior Member
Certified Car Nut
One of mine got water in it between the outer lense and the black part along the edge along the top. I checked for the possibility of leaks elsewhere but couldn't find any.
#6
Senior Member
Posts like a Northstar
My vote would also be for the lens gasket seal.
If you attempt to break the seal, beware. On my '92 SSE and '93 SSEi lenses, the seal is a sticky rubbery substance that'* pretty tough to separate, so be careful if you attempt to separate the lense from the seal and reseal it. You could apply an external sealant such as clear silicone to seal the area from the outside instead, but obviously, you'd want to use a minimal amount of silicone for cosmetic reasons.
And note that the moisture/water leak isn't just a cosmetic problem...over time, any exposed metal inside the lens assembly (for example, the bulb socket contacts) will rust and corrode.
If you attempt to break the seal, beware. On my '92 SSE and '93 SSEi lenses, the seal is a sticky rubbery substance that'* pretty tough to separate, so be careful if you attempt to separate the lense from the seal and reseal it. You could apply an external sealant such as clear silicone to seal the area from the outside instead, but obviously, you'd want to use a minimal amount of silicone for cosmetic reasons.
And note that the moisture/water leak isn't just a cosmetic problem...over time, any exposed metal inside the lens assembly (for example, the bulb socket contacts) will rust and corrode.
#7
Senior Member
Posts like a 4 Banger
Join Date: Sep 2008
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
I just spent all of last weekend taking my 92 tails off and resealing them, but they still leak! Now I don't think it'* the seal around the lens and the light bulb housing, but I do think it'* the fact that some of the clear outer lens has separated from the plastic black lines and is allowing water in through the top, plus there'* a bunch of dirt or something in the black laminated area where it should be laminated but has come loose. Stupidly, even after reading a few threads on this, I thought the laminated parts had deteriorated enough to break them apart without baking, and now I've cracked one of them because the bottom portion of the lamination was still good. Can someone please tell me the best way to fix this leak for good so I don't have water in the lights flooding my trunk, I'm getting sick and tired of drying out my trunk full of water every time it rains (which is often in Oregon).
#8
Senior Member
True Car Nut
Anytime you pull the assemblies apart you risk creating leaks or cracking the plastic. Older plastics are UV/weather degraded, and will be much more brittle than you would expect. Use care...or open you wallet for a new one!
#9
Senior Member
True Car Nut
I just spent all of last weekend taking my 92 tails off and resealing them, but they still leak! Now I don't think it'* the seal around the lens and the light bulb housing, but I do think it'* the fact that some of the clear outer lens has separated from the plastic black lines and is allowing water in through the top, plus there'* a bunch of dirt or something in the black laminated area where it should be laminated but has come loose. Stupidly, even after reading a few threads on this, I thought the laminated parts had deteriorated enough to break them apart without baking, and now I've cracked one of them because the bottom portion of the lamination was still good. Can someone please tell me the best way to fix this leak for good so I don't have water in the lights flooding my trunk, I'm getting sick and tired of drying out my trunk full of water every time it rains (which is often in Oregon).
#10
Senior Member
Posts like a 4 Banger
Join Date: Sep 2008
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
That'* good advice. I've put brand new sealant on the connection between the light bulb housing and the lenses so that'* going to be very difficult to get off, so I'm going to try to isolate the leak with your method and just focus on that because I'm almost certain water is getting in through the top of the taillights where the lamination has broken between the black plastic lines and the clear outer lens. Good news is the left taillight did not leak, and that was the one I put more sealant on the top of the taillight where the lid of the trunk comes to rest.
Thread
Thread Starter
Forum
Replies
Last Post
tgunder
Everything Electrical & Electronic
7
06-02-2007 07:48 PM
gene254
1987-1991
3
07-07-2004 08:42 AM