Throttle sticks from idle
Today I noticed if I let my car sit and I start it up I can't move the gas pedal unless I give it a small "oomph". Then it feels like I free'ed it from being stuck somehow. It also did this again just now and when I let off the gas and applied a little throttle while coasting on the road I felt a slight 'give' when I first give throttle...but after that point it moves freely to WOT and back.
I opened the hood and played with the throttle and I felt the same small resistance from idle position. Ideas? |
I would check to see if the throttle plate is closing and binding on the throttle body around the edge of the plate. If the throttle stop screw on the throttle body is turned a little to far out it will allow the throttle plate to close totally against the inside of the throttle body and cause it to stick in the bore. The screw should be adjusted so the throttle plate is just held open enough to eliminate the sticking. The adjustment is very small and the IAC compensates for the tiny bit of additional air bypassing the throttle plate. It could also be a buildup of carbon on the edges of the plate or cable sticking. I had the sticking throttle after replacing the throttle plate on my Sonoma truck and found out about the throttle stop adjustment after buying a new cable. Hope this gives you something to check out.
Flatlander |
Lucky its not happening in the other direction! I actually had that happen once. Playing around with the air filter on my old monte carlo, didn't put the wingnut back on and it somehow found its way to the linkage when I was at 1/2 throttle. scary crap...still don't understand how it did it though, the 'magic wingnut' :D
|
My "MAF Mod" TB did the same thing when I started playing with it. If you look on the "black arm type peice I can't think of the name to" there's the shaft that goes to the TP and the other shaft goes the a large pivot. pull off the "black arm thing" and apply some cleaning and axle grease to the pivot shaft.
|
Uhhh...dame that doesn't make sence bud. :wink:
Try explaining a little more. However I'm slapping myself in the face because I think Flatlander is right. I have the throttle stop screw WAY out to make sure I get a low idle voltage, but at a certain point the voltage won't go down anymore if I keep loosening the screw....so I think its out too far. I'll try that first, thanks. :) |
That makes sense. It's a balancing act between the rotation of the sensor and the screw. It may take a few adjustments to hit it right.
|
I have the same problem after mine sits overnight. I just tap the gas before I put the key in, kinda like my old Catalina when I set the choke on a cold morning. Ahhh...the memories.
Jay |
Re: Throttle sticks from idle
Originally Posted by Allmachtige
Today I noticed if I let my car sit and I start it up I can't move the gas pedal unless I give it a small "oomph". Then it feels like I free'ed it from being stuck somehow. It also did this again just now and when I let off the gas and applied a little throttle while coasting on the road I felt a slight 'give' when I first give throttle...but after that point it moves freely to WOT and back.
I opened the hood and played with the throttle and I felt the same small resistance from idle position. Ideas? |
K, I was playing around with the idle screw for a good 30 minutes and found a "sweet" spot where it just barely keeps the plate open (or so it seems) because I used my delicate ( :lol: ) hands to feel for any resistance...there was none by the time I finished. Tomarrow morning's cold air will show me if my efforts were in vain or not.
|
I'd bet all you need to do is clean the TB. Use a tooth brush, a rag and some carb cleaner. Hold the throttle plate wide open and clean the TB bore. Particularly the perimiter where the throttle plate meets it. Also clean the back side of the throttle plate and it's perimiter. You'll likely find it is all carboned up.
|
All times are GMT -4. The time now is 05:01 PM. |
© 2024 MH Sub I, LLC dba Internet Brands