interferance engine??????
#1
Senior Member
Posts like a Supercharger
Thread Starter
Join Date: Dec 2003
Location: Menomonee Falls, WI
Posts: 158
Likes: 0
Received 0 Likes
on
0 Posts
interferance engine??????
are our engines, series 1 or series 2, interferance engines?????????
i mean if the exhaust vavle or intake vavle are at a full open condition, will the pistion hit the vavle?....the engine nuts would be able to chime in on this one.......if so this would make the timing chain integrity a must!!!!!!!!!!!!!!!!!!!!!!!!!!!
thanks,
nicky!!!
i mean if the exhaust vavle or intake vavle are at a full open condition, will the pistion hit the vavle?....the engine nuts would be able to chime in on this one.......if so this would make the timing chain integrity a must!!!!!!!!!!!!!!!!!!!!!!!!!!!
thanks,
nicky!!!
#4
Senior Member
Posts like a Supercharger
Thread Starter
Join Date: Dec 2003
Location: Menomonee Falls, WI
Posts: 158
Likes: 0
Received 0 Likes
on
0 Posts
crazy, id better get crackin on my timeing chain change before 200000, as anyone on the club ever had their chain brack and piston impact their vavle? If so how bad was the damage?
nicky
nicky
#5
Senior Member
Posts like a Northstar
Join Date: Apr 2004
Location: Minneapolis, MN
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
From what I've personally seen, chain breakage is very rare. I have 220K on my original chain. I have no plans on touching it until the time comes to rebuild the motor.
#8
Guest
Posts: n/a
I feel that there are a few things you need to look at...
The stock lift on a 3800 is .250 intake and .255 exahust( Too lazy to look up the numbers for diffrent years as they stayed pretty close) then multiply by 1.6 and you have the totall lift at the valve...
I think it should be .400 intake and .408 exahust...
The look at where exactly the valves are located in relation to the dish in the piston... Will the vlaves be in the general area of the dish?
The the compression.... The 8.5 to 1 compression pistons have a decent dish in them, if you look at the series II NA'd 3800 the 9.4 to 1 compression pistons are almost flat...
I have never seen an 8.5-1 compression 3800 kill a valve... But I have seen the old school 3.0 Buick V6 9.0 to 1 compression crush valves when the timming chain went...
But the cam lobe lift was 3.89 using conventional lifters... Each piston had 2 valve marks...And one cylinder had a chunk of valve imbeded in the head and piston... Not pretty...
But then again I have yet to hear of an 89-current 3800 jumpping time , or for that matter crushing valves... But I'll bet as we see more performance I'll bet someone will find out for sure... Hopefully not here on BC tho..
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
The stock lift on a 3800 is .250 intake and .255 exahust( Too lazy to look up the numbers for diffrent years as they stayed pretty close) then multiply by 1.6 and you have the totall lift at the valve...
I think it should be .400 intake and .408 exahust...
The look at where exactly the valves are located in relation to the dish in the piston... Will the vlaves be in the general area of the dish?
The the compression.... The 8.5 to 1 compression pistons have a decent dish in them, if you look at the series II NA'd 3800 the 9.4 to 1 compression pistons are almost flat...
I have never seen an 8.5-1 compression 3800 kill a valve... But I have seen the old school 3.0 Buick V6 9.0 to 1 compression crush valves when the timming chain went...
But the cam lobe lift was 3.89 using conventional lifters... Each piston had 2 valve marks...And one cylinder had a chunk of valve imbeded in the head and piston... Not pretty...
But then again I have yet to hear of an 89-current 3800 jumpping time , or for that matter crushing valves... But I'll bet as we see more performance I'll bet someone will find out for sure... Hopefully not here on BC tho..
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Thread
Thread Starter
Forum
Replies
Last Post
19bonnie95
1992-1999
27
06-14-2006 01:14 AM