Some rainy day pics (+ PEM install pics)
#1
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2002
Location: Sauk Centre, MN
Posts: 5,459
Likes: 0
Received 0 Likes
on
0 Posts
Some rainy day pics (+ PEM install pics)
Notice no more gold pin-striping? I've still got on black pin-stripe, but plan on removing it and replacing it with a 1/2" black stripe because it looked so sinister in the photoshop my buddy did the other day.
May also remove the 'Blown' emblems for the sleeper look.
Also, the tires I just bought and have on the car now (as seen in pics are 235/55/16 Dayton Daytona V-rated tires).
May also remove the 'Blown' emblems for the sleeper look.
Also, the tires I just bought and have on the car now (as seen in pics are 235/55/16 Dayton Daytona V-rated tires).
#5
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2002
Location: Sauk Centre, MN
Posts: 5,459
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by J Wikoff
Did you notice a difference?
Notice the weld where the # 3 runner meets the main pipe -it'* cracked almost all the way around. Then I tore the heat shield off the crossover and found the nasty crack that I figure was a major reason for my loapy idle.
Benefit'* I know of without scanning after installation:
#1: No more loapy idle.
#2: High rpms under load feel a lot smoother -engine revs under load almost as smooth as the Series II L67 in my brothers 97 SSEi.
#3: Even though I've been battling fouled plugs, a chopped # plug wire, and detonation (I need to work on my fuel system now), it pulls harder and smoother than ever before.
#4: 5 minutes after turning the engine off after some hard driving I can grab the manifolds with my bare hands and the feel hot after about 3-4 seconds -couldn't go near the stock one'* for almost an hour without getting burnt before.
#7
Senior Member
True Car Nut
Thread Starter
Join Date: Dec 2002
Location: Sauk Centre, MN
Posts: 5,459
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 95naSTA
I'm liking the Blown. And those PEMs look clean as H*** in there.
Any chance we could get a butt shot of the 96+ rear?
Any chance we could get a butt shot of the 96+ rear?
#8
Senior Member
Posts like a Turbo
Join Date: Oct 2005
Location: Northern Indiana
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
I wonder if very many people(besides BC) notice you have a 95 front with a 96 rear. I agree with you, you should remove the Blown emblem for more of a sleeper look
#10
Senior Member
Certified GM nut
Join Date: Sep 2005
Location: Home Sweet Home in New York
Posts: 2,009
Likes: 0
Received 0 Likes
on
0 Posts
PEMS look great!
You're missing the spark plug wire routing thingy there, gonna lose another wire if you're not careful. Not like I speak from experience in this matter... No not at all.. .
You're missing the spark plug wire routing thingy there, gonna lose another wire if you're not careful. Not like I speak from experience in this matter... No not at all.. .
Thread
Thread Starter
Forum
Replies
Last Post
m1030w6
Your Ride: GM Pictures & Videos
11
04-15-2008 07:49 PM
darkside999
Everything Electrical & Electronic
4
09-09-2006 10:33 PM
singscountry1967
Your Ride: GM Pictures & Videos
33
06-06-2006 09:16 AM