Daily driver fiero help (pic heavy)
01-05-2015, 01:17 AM
#1
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Dec 2014
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Daily driver fiero help (pic heavy)
Back in October.
My bone stock 2.5 fiero has been burning oil and smoking sense I bought her.
I have finally got to a point at my job where I can
afford to give my sad little fiero the proper care it needs.
later-
So today I found that my head gasket was leaking. I've never used new head bolts like these.
The 3 steps for setting them seem to be beyond me....
I pulled the valve cover and cleaned the oil off of everything.
Re-set them and we will see how it goes.
Anything else I could check?
Oil and coolant was spurting out behind the header shield.
My bone stock 2.5 fiero has been burning oil and smoking sense I bought her.
I have finally got to a point at my job where I can
afford to give my sad little fiero the proper care it needs.
later-
So today I found that my head gasket was leaking. I've never used new head bolts like these.
The 3 steps for setting them seem to be beyond me....
I pulled the valve cover and cleaned the oil off of everything.
Re-set them and we will see how it goes.
Anything else I could check?
Oil and coolant was spurting out behind the header shield.
01-05-2015, 07:33 AM
#2
Senior Member
True Car Nut
as far as the torque they are stepped in the proper inside out pattern to make sure it draws down evenly and seals right. you cant just retorque it if its bad should undo it all and redo the steps
01-05-2015, 11:09 AM
#3
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Dec 2014
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Ok. I was just worried I would haft to buy new head bolts and a head gasket.
My block is iron, but I've pulled treads out of Honda aluminum blocks before.
Thank you jwfirebird!
My block is iron, but I've pulled treads out of Honda aluminum blocks before.
Thank you jwfirebird!
01-05-2015, 11:19 AM
#5
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Dec 2014
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
02-22-2015, 02:10 PM
#6
Member
Posts like a V-Tak
Just did one on my 86-olds (not fiero) Likely a head gasket? heads will warp & crack too! The blocks /rebuilt are on ebay for 199.00 bux - cheap enough!! Heads also avail. look close & remember what code engine u have as heads are different!! I just bought a redone head there for 69.bux- from old machinest-had 1 left over. ur engine is likely a "R"code so just be sure!!
02-22-2015, 03:31 PM
#7
Senior Member
True Car Nut
What a freakin' nightmare those Fiero'* were.....
There were enough campaigns on them.....wrapping all the heat tape around the harnesses, the heat shields, and of course the broken bolts on the exhaust manifolds...
And in a salt area, the underbody would just rot out......
Sad, that just when they were about to redesign and make it a better vehicle, that they dropped it.....
The Formula with the V-6 and a manual tranny was a swift little car....
There were enough campaigns on them.....wrapping all the heat tape around the harnesses, the heat shields, and of course the broken bolts on the exhaust manifolds...
And in a salt area, the underbody would just rot out......
Sad, that just when they were about to redesign and make it a better vehicle, that they dropped it.....
The Formula with the V-6 and a manual tranny was a swift little car....
02-25-2015, 10:49 AM
#8
Artist
True Car Nut
Check your valve seals. That'* supposedly one of the common issues on Fieros that cause them to smoke. It was starting to cause mine to smoke, but I wound up selling it before it became an issue 
Thread
Thread Starter
Forum
Replies
Last Post
spidey3479
Your Ride: GM Pictures & Videos
5
09-13-2006 01:14 PM
alec_b
Your Ride: GM Pictures & Videos
2
10-09-2005 06:31 PM