Polishing an M90
#12
Senior Member
True Car Nut
Join Date: Feb 2003
Location: Philly
Posts: 4,508
Likes: 0
Received 0 Likes
on
0 Posts
You might get close with paints but you'll never get the mirror like finish of polished aluminum.
Here'* some stuff I did the hard way..
For the most part it'* sand paper from 220 to 2000 then aluminum polish with a buffing wheel and a dremel with strips of different sand paper for the tight spots. No wet sanding or compounds.
(This pan is stamped steel.. fml)
Polishing stuff is heartbreaking.. Out of all that, the master cylinder got brake fluid on it and messed up the clear powder coat. The wheels got the clear powder coat nicked and started to spiderweb oxidize under. That alt cover started to do the same. And that stamped steel pan started to rust in tiny little spots under the clear. Steel is workk to polish too.
I opted to get stuff powder coated clear since it will take heat and not yellow.. and I know I don't really feel like repolishing crap every season. So much for that.
I still haven't given up though. I'm going to give Zoop sealer a try. When I first looked into it there were a lot of negative forum responces. More recently I think people actually followed the directions and have had success with it.
Here'* some stuff I did the hard way..
For the most part it'* sand paper from 220 to 2000 then aluminum polish with a buffing wheel and a dremel with strips of different sand paper for the tight spots. No wet sanding or compounds.
(This pan is stamped steel.. fml)
Polishing stuff is heartbreaking.. Out of all that, the master cylinder got brake fluid on it and messed up the clear powder coat. The wheels got the clear powder coat nicked and started to spiderweb oxidize under. That alt cover started to do the same. And that stamped steel pan started to rust in tiny little spots under the clear. Steel is workk to polish too.
I opted to get stuff powder coated clear since it will take heat and not yellow.. and I know I don't really feel like repolishing crap every season. So much for that.
I still haven't given up though. I'm going to give Zoop sealer a try. When I first looked into it there were a lot of negative forum responces. More recently I think people actually followed the directions and have had success with it.
#13
Senior Member
Posts like a Northstar
Thread Starter
Join Date: Apr 2009
Location: Indianapolis, Indiana
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
Wow all of that looks really nice. You've got show car qaulity pieces there. However im not sure i have the time for such an extensive job as that. Just lookin to spruce up the bay a little bit.
#14
Okie Hokie
Posts like a Camaro
Join Date: Dec 2008
Location: Durant, Ok 74701
Posts: 1,107
Likes: 0
Received 0 Likes
on
0 Posts
^^ mine before it went in the car, it was out and needed cleaning so we painted it to make it all purty as well... crappy tanish color was nasty, now it looks great *Silver Engine Enamel*
Agreed paint goes along way, but it doesn't look as good as hours of dedicated polishing and coating.
#16
Okie Hokie
Posts like a Camaro
Join Date: Dec 2008
Location: Durant, Ok 74701
Posts: 1,107
Likes: 0
Received 0 Likes
on
0 Posts
Taken before the 1st engine spun a bearing... looks good but red hoses would accent nicely... silicon hoses work or would i need something stouter? I used silicon hoses on my miata years ago, but they flattened out on vacuum side and started causing problems, looked great, functionality not so good
#18
Senior Member
True Car Nut
Join Date: Jun 2007
Location: New Lenox, IL
Posts: 2,478
Likes: 0
Received 0 Likes
on
0 Posts
Where did you get that wrinkle paint?
Thread
Thread Starter
Forum
Replies
Last Post
harofreak00
Your Ride: GM Pictures & Videos
19
02-09-2006 11:49 PM
94 SSE with Sizzle
Performance, Brainstorming & Tuning
8
03-05-2004 11:23 PM