thoughts
#1
Senior Member
Posts like a Corvette
Thread Starter
thoughts
I was cruising on another 3800 site that I will not name but there was a guy who had done the zzp m90 to the l36 and well as the story goes he left the BBV open and said it felt stronger even if he wasn't getting boost. That got me to thinking and well if I were to swap the topend for a L67 topend wouldn't that be better for flow even if i don't run the blower to fast. I am just looking for something that would help with power and also mileage up here in the altitudes because the L36 falls on it'* face going over the mountains. Just thinking out loud here any input is appreciated
#3
Senior Member
Posts like a Supercharger
Join Date: Dec 2005
Location: Ohio
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
the L67 heads and intake will flow better than an L36
story goes he left the BBV open and said it felt stronger even if he wasn't getting boost
-Jeremiah
#5
M90'* love the higher compression of the L36'*. AT MIGPC a GP GT with only a ZZP SS M90 kit dyno'd 253WHP and over 300ft/lbs. with a 4.0" pulley!
People who run the ZZP SS M90 kit or have done a L67 top end swap have had GREAT success with it. IIRC someone on here has done the swap to their GP GT.
People who run the ZZP SS M90 kit or have done a L67 top end swap have had GREAT success with it. IIRC someone on here has done the swap to their GP GT.
#6
Senior Member
Posts like a Supercharger
Join Date: Dec 2005
Location: Ohio
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
People who run the ZZP SS M90 kit or have done a L67 top end swap have had GREAT success with it. IIRC someone on here has done the swap to their GP GT.
#8
Senior Member
Posts like a Supercharger
Join Date: Dec 2005
Location: Ohio
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
IIRC ZZP said that an L36 bottom will make ~ 5% more power then the a L67 bottom. So the more power you make the bigger the WHP #'* will be.
Top swap can run a full size I/C, ZZP can only run SSIC, ect. The ease of the instal is the big plus for ZZP kit since you dont have to pull your heads.
#9
Senior Member
Posts like a Corvette
Thread Starter
so if I called ed morad and asked if I could get all that for say 500 and then send my pcm to intense and get reburned and see where I am at there. but would I need a new pulley on the bottom block for the topend to work right
#10
Senior Member
Posts like a Supercharger
Join Date: Dec 2005
Location: Ohio
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
It will most likely be a little more than $500 for everything, unless its an extremely high mileage take off. We go thru all our top swaps, cleaning, new */c oil, inspection, new */c coupler, viton valve seals, ect. Here is everything I can remember off the tp of my head:
complete M90
L67 TB (97/98 work very well with the swap, if modified correctly)
L67 Fuel rail
6 L67 Injectors
MAP sensor
MAP plug
BBV plug (sensor should be on the blower)
L67 heads (can be stripped, and use everything of your L36 heads)
L67 Valve covers
Valve cover gaskets
new rocker bolts (maybe)
*/C belt
L67 ICM bracket (97-98 GTs have the correct bracket already)
tensioner w/ pulley (need the nut also, there are only 3 this style on the entire car)
idler puller for ICM bracket
Idler pulley w/ stand off
L67 crank pulley (dampner)
head gaskets
head studs or bolts
bolts for idler stand off (3, the L36 ones are to short and are only there to plug the coolant jackets)
L67 LIM
LIM gasket (alum. one is reccommended)
*/C gasket
*/C gasket O-rings
PCM work
I hope I didnt miss anything! Most ppl. have upwards of $1000 into the top swap when doing themselves. We are currently working on lowering our pricing, and are expecting a $1400 installed pricetag-with NOTHING more to buy (other than more mods). And you don't even have to get dirty .
You could send your PCm to Intense, and Tim King has great knowledge of tuning the L36 block, however sending the PCM to anyone is a bad idea. The L36 is not as tolerant as the L67, and one little "oops", and you'll need to be calling Ed again. Your best on tuning is finding someone local, or drive to Intense. The base file is VERY easy to setup.
L67 engine param. with L36 trans params. You can drive it like that fine for a long while with an AFC to tune fuelng. But again your best bet is to have some tuning/driving/scanning your car before doing any changes.
-Jeremiah
complete M90
L67 TB (97/98 work very well with the swap, if modified correctly)
L67 Fuel rail
6 L67 Injectors
MAP sensor
MAP plug
BBV plug (sensor should be on the blower)
L67 heads (can be stripped, and use everything of your L36 heads)
L67 Valve covers
Valve cover gaskets
new rocker bolts (maybe)
*/C belt
L67 ICM bracket (97-98 GTs have the correct bracket already)
tensioner w/ pulley (need the nut also, there are only 3 this style on the entire car)
idler puller for ICM bracket
Idler pulley w/ stand off
L67 crank pulley (dampner)
head gaskets
head studs or bolts
bolts for idler stand off (3, the L36 ones are to short and are only there to plug the coolant jackets)
L67 LIM
LIM gasket (alum. one is reccommended)
*/C gasket
*/C gasket O-rings
PCM work
I hope I didnt miss anything! Most ppl. have upwards of $1000 into the top swap when doing themselves. We are currently working on lowering our pricing, and are expecting a $1400 installed pricetag-with NOTHING more to buy (other than more mods). And you don't even have to get dirty .
You could send your PCm to Intense, and Tim King has great knowledge of tuning the L36 block, however sending the PCM to anyone is a bad idea. The L36 is not as tolerant as the L67, and one little "oops", and you'll need to be calling Ed again. Your best on tuning is finding someone local, or drive to Intense. The base file is VERY easy to setup.
L67 engine param. with L36 trans params. You can drive it like that fine for a long while with an AFC to tune fuelng. But again your best bet is to have some tuning/driving/scanning your car before doing any changes.
-Jeremiah