Custom restoration project
#1
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2007
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Custom restoration project
ok guys,... I can't believe that I found this,... will post pictures soon.
1970 Pontiac Catalina
ALL ORIGIONAL PARTS
no motor or trans (but it'* a project car, those just get rebuilt or scrapped anyway)
VERY little rust on the body (underbody'll need a little work)
and all this for only $300 (or trade the salvage guy my 2 old 1/2 parted out cavaliers hehehe)
so,... any ideas on this???
1970 Pontiac Catalina
ALL ORIGIONAL PARTS
no motor or trans (but it'* a project car, those just get rebuilt or scrapped anyway)
VERY little rust on the body (underbody'll need a little work)
and all this for only $300 (or trade the salvage guy my 2 old 1/2 parted out cavaliers hehehe)
so,... any ideas on this???
#2
Senior Member
True Car Nut
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Re: Custom restoration project
Originally Posted by blackwolfdarcon
ok guys,... I can't believe that I found this,... will post pictures soon.
1970 Pontiac Catalina
ALL ORIGIONAL PARTS
no motor or trans (but it'* a project car, those just get rebuilt or scrapped anyway)
VERY little rust on the body (underbody'll need a little work)
and all this for only $300 (or trade the salvage guy my 2 old 1/2 parted out cavaliers hehehe)
so,... any ideas on this???
1970 Pontiac Catalina
ALL ORIGIONAL PARTS
no motor or trans (but it'* a project car, those just get rebuilt or scrapped anyway)
VERY little rust on the body (underbody'll need a little work)
and all this for only $300 (or trade the salvage guy my 2 old 1/2 parted out cavaliers hehehe)
so,... any ideas on this???
#3
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2007
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
looking at an Edelbrock 383 crate motor to drop in, the badge on the fender says it'* the factory 6.6l 400ci, but I can't find any that aren't in a firebird
#4
Senior Member
True Car Nut
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by blackwolfdarcon
looking at an Edelbrock 383 crate motor to drop in, the badge on the fender says it'* the factory 6.6l 400ci, but I can't find any that aren't in a firebird
#6
Junior Member
Join Date: May 2006
Location: BonnevilleHell
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Re: Custom restoration project
Nice Score!
It will likely be a rust bucket for so little, but then, most restorations start out that way anywho. You got a frame and a VIN #, which is pretty much all you need. The car is old enough to be exempt from damn near everything, so the sky is the limit as far as what you can do to it.
As to suggestions on what to do. Well, assume the worst. Dissassemble the entire car down to a frame. Take huge amounts of pictures...you'll need them later. Bag & Tag everything into logical groups.
Then, start with cleaning off the bare frame and having it fixed. The frame is the basis for everything else go on, so it needs to be perfect.
Then start cleaning, inspecting, replacing until the entire car is reassembled.
These kind of projects can take years to do by yourself. (I'd estimate close to 1500 man hours to do a complete restoration.)
Good part about it is that you can work on major sub-assemblies in parallel. When you get bored with one task, you can stop and go work on another area.
Hmmm....motors. I'll second the Big Block idea, if you can afford it. Second choice would be the 400 Pontiac V8 if you can find one. 3rd choice would be a late model Small Block Chevy 350 with Fuel Injection. You'll never find the original motor with the correct serial number, so you're not hurting the cars value by substituting a different V8 from the GM family. Transmission, only one choice IMHO if you plan on driving the car on the road...the 700R4. Fitted with the vette accumulators, 2nd band pistons, and all the bulletin upgrades, it will be plenty strong enough to handle such a heavy car. If you go carb, there are tricks to getting the TCC to function as well.
One thing to budget...disk brakes on at least the front axle. Drums on all four corners suck.
It will likely be a rust bucket for so little, but then, most restorations start out that way anywho. You got a frame and a VIN #, which is pretty much all you need. The car is old enough to be exempt from damn near everything, so the sky is the limit as far as what you can do to it.
As to suggestions on what to do. Well, assume the worst. Dissassemble the entire car down to a frame. Take huge amounts of pictures...you'll need them later. Bag & Tag everything into logical groups.
Then, start with cleaning off the bare frame and having it fixed. The frame is the basis for everything else go on, so it needs to be perfect.
Then start cleaning, inspecting, replacing until the entire car is reassembled.
These kind of projects can take years to do by yourself. (I'd estimate close to 1500 man hours to do a complete restoration.)
Good part about it is that you can work on major sub-assemblies in parallel. When you get bored with one task, you can stop and go work on another area.
Hmmm....motors. I'll second the Big Block idea, if you can afford it. Second choice would be the 400 Pontiac V8 if you can find one. 3rd choice would be a late model Small Block Chevy 350 with Fuel Injection. You'll never find the original motor with the correct serial number, so you're not hurting the cars value by substituting a different V8 from the GM family. Transmission, only one choice IMHO if you plan on driving the car on the road...the 700R4. Fitted with the vette accumulators, 2nd band pistons, and all the bulletin upgrades, it will be plenty strong enough to handle such a heavy car. If you go carb, there are tricks to getting the TCC to function as well.
One thing to budget...disk brakes on at least the front axle. Drums on all four corners suck.
#8
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2007
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
actually, after a little more research, I'm thinking that the 455 idea is a good one, plenty of motor, and lots of possible add-ons, well, I'll get started on it sometime this summer, and do my best to post pics along the way.
#9
Junior Member
Posts like a Ricer Type-R
Thread Starter
Join Date: Feb 2007
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
haha,... found the motor I'm definitely getting.
click here ---->http://www.proformanceunlimited.com/...455_450tk.html
have already decided to do the Holly carb upgrade
click here ---->http://www.proformanceunlimited.com/...455_450tk.html
have already decided to do the Holly carb upgrade