2003 SSEi mirror question
#1
Senior Member
Certified GM nut
Thread Starter
Join Date: Jul 2004
Location: West Point, Utah - Village Idiot
Posts: 1,606
Likes: 0
Received 2 Likes
on
2 Posts
2003 SSEi mirror question
I drove a couple 2003’* over the weekend, and noticed on one car that when I backed up the right outside mirror automatically adjusted down to see what might be lurking about near the back of the car. The other car didn’t do this. Is this some sort of option that may be on some cars but not on others, or is it something that can be programmed on/off, or is one car just broken?
Not sure if this is a mechanical issue or if this should be in general chat. MODS, you be the judge!
Earn your keep. :P
Not sure if this is a mechanical issue or if this should be in general chat. MODS, you be the judge!
Earn your keep. :P
#2
Member
Posts like a V-Tak
Join Date: Apr 2006
Location: McVeytown, PA
Posts: 82
Likes: 0
Received 0 Likes
on
0 Posts
I am pretty sure this it is programmed into the driver setting. You can turn it on and off when programming driver settings. I think it is a basic option more or less put on all atleast ssei'*
#3
RIP
True Car Nut
If you want all of the information on it, you can read it here.
OUTSIDE MIRROR DESCRIPTION AND OPERATION
Or - the part that addresses your specific question is this.
OUTSIDE MIRROR DESCRIPTION AND OPERATION
Or - the part that addresses your specific question is this.
MEMORY MIRRORS - PARALLEL PARKING MODE
If the vehicle is equipped with memory mirrors, it is equipped with the parallel parking mode feature. For this feature, the driver door module (DDM) communicates with the powertrain control module (PCM) over the class 2 data link. When the gear selector is shifted to reverse, the PCM transmits this status via a class 2 message to the DDM. The DDM sends this message on to the front passenger door module (PDM) over the power door serial data circuit. The PDM then applies battery voltage and ground to the vertical motor of the RH outside rear view mirror to tilt the mirror down 7 degrees . This allows the driver to see the curb while parallel parking. When the gear selector is shifted out of reverse, the PDM drives the vertical mirror motor to return the mirror to its previous position.
If the vehicle is equipped with memory mirrors, it is equipped with the parallel parking mode feature. For this feature, the driver door module (DDM) communicates with the powertrain control module (PCM) over the class 2 data link. When the gear selector is shifted to reverse, the PCM transmits this status via a class 2 message to the DDM. The DDM sends this message on to the front passenger door module (PDM) over the power door serial data circuit. The PDM then applies battery voltage and ground to the vertical motor of the RH outside rear view mirror to tilt the mirror down 7 degrees . This allows the driver to see the curb while parallel parking. When the gear selector is shifted out of reverse, the PDM drives the vertical mirror motor to return the mirror to its previous position.
#5
Senior Member
Certified GM nut
Join Date: Jun 2004
Posts: 1,933
Likes: 0
Received 0 Likes
on
0 Posts
My 01 has this feature. Be advised, there is a tech pub out about the 00 to 02 mirror tilting down and not restoring to the original position so check it before you buy. My mirror is a victim of this.
Document ID# 854088
2001 Pontiac Bonneville
Outside Rearview Mirror Memory Recall Does Not Function Properly When Using Remote Keyless Entry (RKE) Door Unlock Button (Replace Dr Lk and O/* R/View Mirror and P/W Control Module) #02-08-64-003 - (Jan 25, 2002)
Outside Rearview Mirror Memory Recall Does Not Function Properly When Using Remote Keyless Entry (RKE) Door Unlock Button (Replace Dr Lk & O/* R/View Mirror & P/W Control Module)
2000-2002 Buick LeSabre Limited
2001-2002 Oldsmobile Aurora
2000-2002 Pontiac Bonneville
With RPO A45
Condition
Some customers may comment that the outside rearview mirrors do not return to the memory recall position when the Remote Keyless Entry (RKE) door unlock button is used to enter the vehicle.
Cause
This condition may be due to a unique software issue within the driver'* door lock and the outside rearview mirror and power window control module assembly (DDM).
Correction
Modifications have been made to the DDM software. Replace the DDM. Refer to Door Control Module Replacement in the Doors sub-section in the Service Manual.
Parts Information
Part Number
Description
25739948
Module Asm-Dr Lk & O/* R/View Mirror & P/W Control
Parts are currently available from GMSPO.
Warranty Information
For vehicles repaired under warranty, use:
Labor Operation
Description
Labor Time
N4851
Module Asm-Driver'* Door Control-Replace
0.3 hr
2001 Pontiac Bonneville
Outside Rearview Mirror Memory Recall Does Not Function Properly When Using Remote Keyless Entry (RKE) Door Unlock Button (Replace Dr Lk and O/* R/View Mirror and P/W Control Module) #02-08-64-003 - (Jan 25, 2002)
Outside Rearview Mirror Memory Recall Does Not Function Properly When Using Remote Keyless Entry (RKE) Door Unlock Button (Replace Dr Lk & O/* R/View Mirror & P/W Control Module)
2000-2002 Buick LeSabre Limited
2001-2002 Oldsmobile Aurora
2000-2002 Pontiac Bonneville
With RPO A45
Condition
Some customers may comment that the outside rearview mirrors do not return to the memory recall position when the Remote Keyless Entry (RKE) door unlock button is used to enter the vehicle.
Cause
This condition may be due to a unique software issue within the driver'* door lock and the outside rearview mirror and power window control module assembly (DDM).
Correction
Modifications have been made to the DDM software. Replace the DDM. Refer to Door Control Module Replacement in the Doors sub-section in the Service Manual.
Parts Information
Part Number
Description
25739948
Module Asm-Dr Lk & O/* R/View Mirror & P/W Control
Parts are currently available from GMSPO.
Warranty Information
For vehicles repaired under warranty, use:
Labor Operation
Description
Labor Time
N4851
Module Asm-Driver'* Door Control-Replace
0.3 hr
#6
Senior Member
Posts like a Camaro
Originally Posted by 2000SilverBullet
That'* right. You can toggle this feature off or on using the DIC personization feature.
#7
Senior Member
Certified GM nut
Thread Starter
Join Date: Jul 2004
Location: West Point, Utah - Village Idiot
Posts: 1,606
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by chadow427
Originally Posted by 2000SilverBullet
That'* right. You can toggle this feature off or on using the DIC personization feature.