Polishing an M90
#11
Junior Member
Posts like a Ricer Type-R
I know there is a difference in the inlet design work. I know generally what it is, but need confirmation on the inlet relationship to the bypass.
I believe there is more gain in performance for the GenV in the inlet port than the rotor clearances.
Bill, the transition from the bypass to the compressor chamber is exactly what I was thinking.
I believe there is more gain in performance for the GenV in the inlet port than the rotor clearances.
Bill, the transition from the bypass to the compressor chamber is exactly what I was thinking.
#12
Senior Member
True Car Nut
After we talked last night, Bill, I went out and polished my supercharger too. Then I took it out and it had a TON more power.....and then the alarm went off and I woke up....
#13
Senior Member
True Car Nut
Join Date: May 2005
Location: _Phoenix, AZ_ _WCBF '05, '06, '07 Survivor_ ____NEBF '07 Remnant___
Posts: 3,448
Likes: 0
Received 6 Likes
on
6 Posts
Amazing Excellent work.
I assume we will be getting a report on "before and after" changes (at least with the butt dyno)?
I assume we will be getting a report on "before and after" changes (at least with the butt dyno)?
#14
Senior Member
True Car Nut
Join Date: Jan 2006
Location: NEBF:06,07 | NYBF:06,07 | ONBF:06,07 | CNBF:06 & more............
Posts: 8,029
Likes: 0
Received 0 Likes
on
0 Posts
<------ "Sneeks to CT and takes the M90"
Good job there Bill, Now to do the out Side but then Haro might Take it
I cant wait to you put it on and see what diffrence it made
Good job there Bill, Now to do the out Side but then Haro might Take it
I cant wait to you put it on and see what diffrence it made
#16
DINOSAURUS BOOSTUS
Expert Gearhead
Thread Starter
Last night with Lash on the cell phone..
2 cans of brake cleaner
1 TB gasket
1 SC to intake w/ O rings gasket
$13 out the door with gaskets arriving today.
I still need to drill/tap and remove the needle bearings then press the new ones back in to the casing. After that.. clean and reinstall the waste gate.
2 cans of brake cleaner
1 TB gasket
1 SC to intake w/ O rings gasket
$13 out the door with gaskets arriving today.
I still need to drill/tap and remove the needle bearings then press the new ones back in to the casing. After that.. clean and reinstall the waste gate.
#19
DINOSAURUS BOOSTUS
Expert Gearhead
Thread Starter
Originally Posted by Greyhare
Nice work Bill.
Before and after dyno runs would be interesting.
When do we find out how small you can go with the pulley?
Before and after dyno runs would be interesting.
When do we find out how small you can go with the pulley?
5 allen screws and er uh.. we find out.. (although I will need oversized tensioner or smaller belt to do that.)
#20
Junior Member
Posts like a Ricer Type-R
Porting/smoothing the outlet alone may make enough difference for a tenth of an inch diameter drop on the pulley.
The inlet work may be good for another (without KR).
Bill will know shortly.
I'm convinced my SC porting and polishing is one of the primary reasons (besides the ported LIM and EM'*) that I was able to go so small in pulley size on a Gen3.
The inlet work may be good for another (without KR).
Bill will know shortly.
I'm convinced my SC porting and polishing is one of the primary reasons (besides the ported LIM and EM'*) that I was able to go so small in pulley size on a Gen3.