1996 Keyless entry
05-23-2006, 01:22 AM
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2006
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
1996 Keyless entry
OK gent and ladies, my keyless entry/remote start no longer works. It used to, but it has also sat in a garage for almost a year. I have tried this
and all the variations I have seen posted. When I connect the 4 and 8 pins on the DLC, shut the door and put the ignition to ON, The locks cycle lock/unlock. I tried programming both remotes, and nada.
Am I missing anything?
Thankx Dave
1. Turn the ignition switch OFF.
Use a fused jumper wire in order to jumper the DLC terminal 8 (BLK/WHT) to terminal 4 (BLK).
2. Close all of the doors.
3. Turn the ignition switch ON. The doors will cycle to lock.
4. Press and hold the LOCK button and the UNLOCK button on one transmitter. After a 30 second delay the doors will lock and unlock.
Important
Do not turn the ignition OFF or the first transmitter will become inoperative.
5. In order to program extra transmitters, repeat step 4.
6. Disconnect the fused jumper wire from the DLC.
Use a fused jumper wire in order to jumper the DLC terminal 8 (BLK/WHT) to terminal 4 (BLK).
2. Close all of the doors.
3. Turn the ignition switch ON. The doors will cycle to lock.
4. Press and hold the LOCK button and the UNLOCK button on one transmitter. After a 30 second delay the doors will lock and unlock.
Important
Do not turn the ignition OFF or the first transmitter will become inoperative.
5. In order to program extra transmitters, repeat step 4.
6. Disconnect the fused jumper wire from the DLC.
Am I missing anything?
Thankx Dave
05-23-2006, 07:41 AM
#3
DINOSAURUS BOOSTUS
Expert Gearhead
Originally Posted by DeeMutz
OK gent and ladies, my keyless entry/remote start no longer works. It used to, but it has also sat in a garage for almost a year. I have tried this
05-23-2006, 07:52 AM
#4
Senior Member
Certified Car Nut
Join Date: Jul 2003
Location: Robbinsdale, MN
Posts: 15,408
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, Bill is probably on to something. I have 2 remotes for my car. The factory remotes, and the one for the remote starter. Both will work the locks (but in different ways), but only the factory remotes program in the above manner.
Does yours look anything like this??
That'* factory. Anything else, you need to find directions for your starter
Does yours look anything like this??
That'* factory. Anything else, you need to find directions for your starter
05-23-2006, 04:02 PM
#6
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2006
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BillBoost37
Originally Posted by DeeMutz
OK gent and ladies, my keyless entry/remote start no longer works. It used to, but it has also sat in a garage for almost a year. I have tried this
MOS95B - no. my remotes do NOT look like that. Mine are square-ish with 4 buttons that are 2X2 ... like this
LOCK - UNLOCK
TRUCK - START
the top of the remotes does say Code/Alarm on them, but like I previously stated, I haven't noticed a control box nor odd wiring.
05-23-2006, 04:05 PM
#7
DINOSAURUS BOOSTUS
Expert Gearhead
Dee...your remotes are aftermarket and that'* why they don't work. The reprogramming you listed is for factory remotes only. Sorry...had a hunch.
05-23-2006, 05:16 PM
#8
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2006
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
there is a bright yellow sticker under the hood, next to the belt route diagram that reads
and after poking around under the hood again, I still can't see anything that isn't stock wiring.
I'm at a loss.
this is the FCC of the back of the remote -- GOH-FOUR
WARNING this vehicle is equipped with a remote controlled car starter. Before servicing this vehicle, remove the main power fuse (red wire) to the car starter or disconnect the vehicle battery
I'm at a loss.
this is the FCC of the back of the remote -- GOH-FOUR
05-23-2006, 06:56 PM
#10
Member
Posts like a V-Tak
Thread Starter
Join Date: May 2006
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
OK after tearing half the underside of the drivers dash apart, I did find a Code Alarm CSM-3 module. who ever did the wiring did a great steth job on it, cuz i had to hunt for it.
I'm about to google for that module to see if I can reprogram it.
where do I find OEM Remotes? ebay?
I like the remote start, but I have until September till I really need it again :p
I'm about to google for that module to see if I can reprogram it.
where do I find OEM Remotes? ebay?
I like the remote start, but I have until September till I really need it again :p