LED's and resistors, how does it all work?
#1
Senior Member
Posts like a Corvette
Thread Starter
Join Date: Jun 2004
Location: Central NJ
Posts: 1,544
Likes: 0
Received 0 Likes
on
0 Posts
LED'* and resistors, how does it all work?
i had an electronics class when i wa slike 10 but i cant rmemeber enough, ok so the standard LED is 3.5-3.8 volts, so which resistor would i need for that, and if i were to add more led'* onto that would i need a different resistor?
#2
Senior Member
Certified Car Nut
Join Date: Jul 2003
Location: Robbinsdale, MN
Posts: 15,408
Likes: 0
Received 0 Likes
on
0 Posts
I think you mean a standard LED is 3.5 to 3.8 Ohms?? Basically, you need tro make sure the LED you are wanting to use is rated for the correct voltage (this will vary, depending upon the LEDs intended use), and add resistance to match the bulb you are replacing (making sure the resistor is also rated for the proper voltage)
OR, if you're just after light output, and not worried if it'* brighter or setting off a Bad Bulb alert, just wire them straight. No extra resistors. NOTE: Without resistance, don't try using LEDs in your turn signals....
OR, if you're just after light output, and not worried if it'* brighter or setting off a Bad Bulb alert, just wire them straight. No extra resistors. NOTE: Without resistance, don't try using LEDs in your turn signals....
#4
DINOSAURUS BOOSTUS
Expert Gearhead
Not sure exactly what you need, but yes...led'* are usually about the voltage you mentioned. For me testing on a pinball circiut board with +5V I use a 180 ohm resistor (cause that'* what the book said)
I would google something like resistor for led 12V and ...guess what?
http://www.kpsec.freeuk.com/components/led.htm
I would google something like resistor for led 12V and ...guess what?
http://www.kpsec.freeuk.com/components/led.htm
#6
DINOSAURUS BOOSTUS
Expert Gearhead
Originally Posted by MOS95B
Wow. I was wrong, huh??
#7
Senior Member
True Car Nut
Join Date: Jan 2003
Location: Bonney Lake/Ellensburg, Washington- WCBF '04, '05, '06, '07 Survivor-
Posts: 7,099
Likes: 0
Received 0 Likes
on
0 Posts
Ok, I'd like to add to this. Why does an LED "bulb" that is rated as a 194 (our corner light bulbs) not work correctly in our cars? Same with the rear turn signals. I REALLY like the way they light up and work but I can't seem to get them to work correctly in the bonne..... :?
#8
Senior Member
Certified Car Nut
Join Date: Jul 2003
Location: Robbinsdale, MN
Posts: 15,408
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by driverjohn2005
Ok, I'd like to add to this. Why does an LED "bulb" that is rated as a 194 (our corner light bulbs) not work correctly in our cars? Same with the rear turn signals. I REALLY like the way they light up and work but I can't seem to get them to work correctly in the bonne..... :?
#9
DINOSAURUS BOOSTUS
Expert Gearhead
Originally Posted by driverjohn2005
Ok, I'd like to add to this. Why does an LED "bulb" that is rated as a 194 (our corner light bulbs) not work correctly in our cars? Same with the rear turn signals. I REALLY like the way they light up and work but I can't seem to get them to work correctly in the bonne..... :?
#10
Senior Member
Posts like a Camaro
Join Date: Oct 2003
Location: Hamilton, Ontario
Posts: 1,074
Likes: 0
Received 0 Likes
on
0 Posts
You cannot measure LEDs with an ohmmeter, they do not have a resistance, rather a reverse voltage potantial, that must be overcome by the source voltage to make the LED work. Since there is technically no resistance, if your source voltage is higher than the rated LED voltage, you must use a resistor in series with the LED to limit the current. The voltage and current ratings are listed by the manufacturer. The correct resistor value can be calculated using Ohms Law V x I = R (v- voltage, I- Current, R- resstance)
just rearrange the equation to find whatever value you are looking for.
What resistance does the turn signal circuit require to work properly? You could put a resistor of this value in parallel with the LEDs and it should work the same way.
just rearrange the equation to find whatever value you are looking for.
What resistance does the turn signal circuit require to work properly? You could put a resistor of this value in parallel with the LEDs and it should work the same way.
Thread
Thread Starter
Forum
Replies
Last Post
Joe Papworth
2000-2005
14
04-04-2013 12:16 PM
Custom88
Audio (and aftermarket electronics)
17
06-25-2004 12:41 PM