Car won't start, stall, die saga continues
#1
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2003
Location: Dallas
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
Car won't start, stall, die saga continues
This has been going on for over a year now. Turns over but won't start, intermittently. Then when it starts it runs for a few minutes then dies and won't start.
95 SSEi. Replaced the crank sensor, twice. Tested ignition module: good. Replaced alternator twice. Each time car is "fixed" it runs for a while; i.e. days/weeks then dies. Now noticed it has No spark.
Hooked up scanner and this is what I see when the car won't start: mode 1 message 0. QDM1,2,4 are in fault, battery voltage is 12.7 volts, C_CERROR (cam/crank error timer) parameter increments each time car turns over and catches a littlebut zeros out when key is turned off. Parameters "Alternator fault detected" = yes, "Engine Hot light" = on, but temp guage is below 200. Also, NO DTC codes are set.
The alternator is brand new, I replaced it twice and the current one is an upgrade. Before buying parts would like some troublshooting advice or if anyone has any ideas.
I am thinking this is a heat-related problem in the Ignition Module area. However, I am confused about the QDM1,2,4. All of them faulting is kinda strange. I don't think it is the PCM cause the engine will run fine when it starts. I think the cam/crank error is due to the QDM problem.
Anyway, any advice or exerience in testing the ignition module, or the Crank/CAM sensor, or the PCM would be greatly appreciated.
Later.
95 SSEi. Replaced the crank sensor, twice. Tested ignition module: good. Replaced alternator twice. Each time car is "fixed" it runs for a while; i.e. days/weeks then dies. Now noticed it has No spark.
Hooked up scanner and this is what I see when the car won't start: mode 1 message 0. QDM1,2,4 are in fault, battery voltage is 12.7 volts, C_CERROR (cam/crank error timer) parameter increments each time car turns over and catches a littlebut zeros out when key is turned off. Parameters "Alternator fault detected" = yes, "Engine Hot light" = on, but temp guage is below 200. Also, NO DTC codes are set.
The alternator is brand new, I replaced it twice and the current one is an upgrade. Before buying parts would like some troublshooting advice or if anyone has any ideas.
I am thinking this is a heat-related problem in the Ignition Module area. However, I am confused about the QDM1,2,4. All of them faulting is kinda strange. I don't think it is the PCM cause the engine will run fine when it starts. I think the cam/crank error is due to the QDM problem.
Anyway, any advice or exerience in testing the ignition module, or the Crank/CAM sensor, or the PCM would be greatly appreciated.
Later.
#3
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2003
Location: Dallas
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the info. I will stop buy on my way home from work today.
I have an ALLDATA subscription, but low and behold they don't have any info on the QDM stuff. Go figure.
Thanks.
I have an ALLDATA subscription, but low and behold they don't have any info on the QDM stuff. Go figure.
Thanks.
#4
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2003
Location: Dallas
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
PROBLEM SOLVED!!!!: Car dies/stalls saga continues.
I still can't believe it. After channging the Crank Sensor, twice, two batteries, two alternators and 2 towings home, and over a year of frustration, I finally think I found the problem with my Bonnie.
I had the ignition module tested several months back and it tested just fine. The guy tested it four time and it passed. This past week I decided to "instrument" the ignition pack (module and coils) and pulled the harness with the idea I was going to put a bunch of test wires in there. Then I thought what the heck and brought it to Autozone to get it tested. 1st test pass. Second test, failed the "Sat"uration test. Third test passed. It was a Wells tester by the way. I decided to wait and do my "instrumentation" thingy instead of paying $160+. Brought it back the next day and tried again. Sure enought, 1st test pass. Second tes, fail "SAT"uration test. Third test passed. ****. Decided to plunk down the $160 and roll the dice. I know I'm a cheap bastard.
It worked! Dammit, I spent over a year troubleshooting this car and it was the damn ignition module after all.
I don't trust her yet though. Been down this road before. Will try her around the neighborhood this weekend and take her into work next week.
Thanks to all in this newsgroup for your help over the past year or so.
Now on to the cup holder, Steering wheel buttons, Traction Contorl, Perf/Touring shift, whining Power Steering, ... problems.
Later.
I had the ignition module tested several months back and it tested just fine. The guy tested it four time and it passed. This past week I decided to "instrument" the ignition pack (module and coils) and pulled the harness with the idea I was going to put a bunch of test wires in there. Then I thought what the heck and brought it to Autozone to get it tested. 1st test pass. Second test, failed the "Sat"uration test. Third test passed. It was a Wells tester by the way. I decided to wait and do my "instrumentation" thingy instead of paying $160+. Brought it back the next day and tried again. Sure enought, 1st test pass. Second tes, fail "SAT"uration test. Third test passed. ****. Decided to plunk down the $160 and roll the dice. I know I'm a cheap bastard.
It worked! Dammit, I spent over a year troubleshooting this car and it was the damn ignition module after all.
I don't trust her yet though. Been down this road before. Will try her around the neighborhood this weekend and take her into work next week.
Thanks to all in this newsgroup for your help over the past year or so.
Now on to the cup holder, Steering wheel buttons, Traction Contorl, Perf/Touring shift, whining Power Steering, ... problems.
Later.
#5
Me too
I think my module is going out also. It just dies, cool off a few minutes, crank it up and all'* well. This has happened only a few times and has ususally set a code for the crank sensor. Well now it isn't setting any codes. Just dies and the computer doesn't catch it. It is happening more often now and it too is grounded until I get around to checking it out. This car has the original module and coils. Maybe time to bring it in for a check.
#7
Senior Member
Posts like a 4 Banger
Join Date: Sep 2003
Location: Illinois
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Does this module control the fuel pump power supply as well? I am getting intermittent fuel pump operation. For instance, when I can't start it (like now), the fuel pump does not turn on for 2 sec or so, when the ignition is first turned on.
Dead on the side of the road for 1.5 weeks now, with no end in sight (see Another Fuel Pump? subject in this forum).
John C. for Nate
Dead on the side of the road for 1.5 weeks now, with no end in sight (see Another Fuel Pump? subject in this forum).
John C. for Nate
#8
Senior Member
Posts like a 4 Banger
Join Date: Sep 2003
Location: Illinois
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
[You may need a good service manual to diagnose the problem...
Try one of our gerheads, maybe one of them will have an idea for you...]
I have a Haynes. I will research more. Point me to the Gearheads!
JC[/quote]
Try one of our gerheads, maybe one of them will have an idea for you...]
I have a Haynes. I will research more. Point me to the Gearheads!
JC[/quote]
#9
Senior Member
Posts like a 4 Banger
Join Date: Sep 2003
Location: Illinois
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jr's3800
Let me see if I can point the Gearheads this way...
I took every fuse out & tested it wit a digital multimeter. Nothing bad. The windows will not roll up, and that keeps me from having it towed to someone. I am thinking that there may be a problem with the ignition switch, that doesn't allow the high amp accesories to run. The flaw in that theory, is that it cranks over just fine.
Thanks for your help.
JC