99 ssei Broke a screw....
#1
Senior Member
Posts like a Supercharger
Thread Starter
Join Date: Apr 2003
Location: Florida
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
99 ssei Broke a screw....
Yes, I bouht a torque wrench (AMPRO) and didn't set it up correctly therefore the screw that screws the VALVE COVER, broke. It'* says to tighten screw at 89 lb. in. and that'* what I did.
Well the question is how can I take the broken screw out the female thread of the valve cover hole. The piece is in there.
And also notice that i have another broken one on the oil pan perimeter to hold the pan.
I feel like crap cause I change the Transmission fluid and filter, engine oil filter and oil. And finally bouth the torque wrench. Everything was excellent until I wanted to find out if the valve cover screws were tight, because I smell oil when the vehicle is hot, but I also wanted to tight those with the proper lb in. I took the book out and did what it told me to do.
Thanx guys, if anybody please share with me a technique how to get screws out, when they're broken.
Well the question is how can I take the broken screw out the female thread of the valve cover hole. The piece is in there.
And also notice that i have another broken one on the oil pan perimeter to hold the pan.
I feel like crap cause I change the Transmission fluid and filter, engine oil filter and oil. And finally bouth the torque wrench. Everything was excellent until I wanted to find out if the valve cover screws were tight, because I smell oil when the vehicle is hot, but I also wanted to tight those with the proper lb in. I took the book out and did what it told me to do.
Thanx guys, if anybody please share with me a technique how to get screws out, when they're broken.
#2
Senior Member
True Car Nut
Join Date: Dec 2003
Location: Corn Fields, IN
Posts: 2,767
Likes: 0
Received 0 Likes
on
0 Posts
Are you sure that you didn't torque the bolts to 89 ft-lbs instead of in-lbs? There are screw extractors that you can buy to get the broken piece out.
#3
Senior Member
Posts like a 4 Banger
Join Date: Sep 2003
Location: Lebanon, Indiana
Posts: 108
Likes: 0
Received 0 Likes
on
0 Posts
John Deere Boy is right, you can buy "Bolt" extractors at most hardware stores. You'll have to predrill the center on the broken bolt first, so keep a couple of rags handy as to not get metal shavings in the heads oil gallery. I thought the same thing he did as well, you might have had it set to Ft-lbs, instead of In-lbs. I think it should have been equivalent to 7.5 Ft Lbs = (89 In-Lbs)
#5
Junior Member
Posts like a Ricer Type-R
Screw extractors work best when you use a cordless drill with the clutch setting. This can simulate an impact wrench action while removing it. Easier to break free.
Leave your valve cover on when doing it to prevent debris from entering the top of the head, or stuff alot of rags in there to protect it. Use a magnet for final cleanup.
You'll also want to re-torque all of the nuts again. You're over-compressing the valve cover seals, which may lead to early failure (assuming you used ft/lbs).
Leave your valve cover on when doing it to prevent debris from entering the top of the head, or stuff alot of rags in there to protect it. Use a magnet for final cleanup.
You'll also want to re-torque all of the nuts again. You're over-compressing the valve cover seals, which may lead to early failure (assuming you used ft/lbs).
#6
Senior Member
Posts like a Supercharger
Thread Starter
Join Date: Apr 2003
Location: Florida
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
Thank you all very much for the advice.
One more question. Wich brand for torque wrench. Or wich one to buy. I bought AMPRO.
Any recomendations?
One more question. Wich brand for torque wrench. Or wich one to buy. I bought AMPRO.
Any recomendations?
#7
Senior Member
True Car Nut
Join Date: May 2003
Location: Lethbridge, Alberta, _______Canada._______ West Coast Bonneville Fest ___05,06,07 Survivor___
Posts: 8,135
Likes: 0
Received 0 Likes
on
0 Posts
personally i will use Mastercraf and craftsman...yet i have been blessed with being able to use a snap-on...to expensive though, as far as a tourqe wrench goes, a specific brand name won't a huge diffrence, unless its the cheapie wal-mart 2 dollar special..then id be skeptical!
#8
Senior Member
True Car Nut
Join Date: Dec 2003
Location: Corn Fields, IN
Posts: 2,767
Likes: 0
Received 0 Likes
on
0 Posts
talk about being blessed---my neighbor loaned us his 3/4" drive snap-on tourque wrench on a more or less permanent basis because he never uses it. this sucker is like 4 or 5 feet long
Thread
Thread Starter
Forum
Replies
Last Post
Pontiacfanatik
Oldsmobile
3
08-10-2011 06:36 AM
Glasuan
Performance, Brainstorming & Tuning
6
09-09-2003 12:45 AM