Changing rotors&brakes
#2
Senior Member
Certified Car Nut
Join Date: Jul 2003
Location: Robbinsdale, MN
Posts: 15,408
Likes: 0
Received 0 Likes
on
0 Posts
If at all possible, get a torque wrench for the reassembly.
And, don't let the calipers just hang by the brake lines. Get some short wires or something to hang thwm up with
And, don't let the calipers just hang by the brake lines. Get some short wires or something to hang thwm up with
#3
Senior Member
True Car Nut
Join Date: Jun 2003
Location: Climax Springs, Missouri
Posts: 2,493
Likes: 0
Received 0 Likes
on
0 Posts
just curious why are you changing the rotors? did you get some high performance ones or something? because if theyre warped you can usually have them turned for about 10-15 bucks for both at most local auto parts stores...thats a heck of a lot cheaper than brand new rotors.
#4
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2005
Location: Kalamazoo, MI, US
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
Getting new ones because my other one(driver'* side front in particular) is F***ed, the pad was a lot lower than the mechanic told me... and before I knew it should have checked myself I was eating away the rotors with some good old metal grinding basically lol...
#5
DINOSAURUS BOOSTUS
Expert Gearhead
Pull the bolts out of the calipers and the metal sleeve they go into. Clean both and apply anti seize or good caliper grease lightly to both.
Ensure the slides for the caliper are clean and apply a light coating to them as well.
Ensure the slides for the caliper are clean and apply a light coating to them as well.
#6
Senior Member
Posts like a Northstar
Join Date: Dec 2005
Location: Indianapolis
Posts: 560
Likes: 0
Received 0 Likes
on
0 Posts
ANTILOCK brakes -
Instead of starting a new thread, i figured I would post this in this thread.
When servicing antilock brakes, is the procedure any different than regular brakes?
I have done antilocks on tow vehicles, and both times, 1/2 the system would fail a few weeks later.
Here is how I do it...
(car on jackstands, wheels and calipers off)
Remove master cylinder cap
Reseat the pistons using a C-clamp or caliper expander (bleeder screws closed.)
Place new pads into calipers.
Replace calipers, wheels...
Once car has the wheels on and on the ground, I start the car, push the brake pedal to the floor a few times until pressure builds, while checking brake fluid every couple pumps. Filling fluid as necessary.
I do not bleed the brakes if they feel firm after this procedure, and the bleeder screw was never loosened.
It works well on non antilock, what am i doing wrong that caused the antilock brake systems to fail?
One was a 1992 caddy Deville, the other was a 1994 Isuzu Rodeo.
Instead of starting a new thread, i figured I would post this in this thread.
When servicing antilock brakes, is the procedure any different than regular brakes?
I have done antilocks on tow vehicles, and both times, 1/2 the system would fail a few weeks later.
Here is how I do it...
(car on jackstands, wheels and calipers off)
Remove master cylinder cap
Reseat the pistons using a C-clamp or caliper expander (bleeder screws closed.)
Place new pads into calipers.
Replace calipers, wheels...
Once car has the wheels on and on the ground, I start the car, push the brake pedal to the floor a few times until pressure builds, while checking brake fluid every couple pumps. Filling fluid as necessary.
I do not bleed the brakes if they feel firm after this procedure, and the bleeder screw was never loosened.
It works well on non antilock, what am i doing wrong that caused the antilock brake systems to fail?
One was a 1992 caddy Deville, the other was a 1994 Isuzu Rodeo.
#7
Member
Posts like a V-Tak
Thread Starter
Join Date: Oct 2005
Location: Kalamazoo, MI, US
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
Didn't get around to doing it today... It was kind of cold and I didn't want to deal with it, I'm going to a heated garage tmw. What tools will I need, to do it and/or make it easier?
#8
DINOSAURUS BOOSTUS
Expert Gearhead
Antilock is no different. It'* all the same and you won't need to touch anything that would be antilock. Be nice to the wires on the back of the brakes..those go to your wheel speed sensor.
#9
Senior Member
True Car Nut
Originally Posted by impatient99
Remove master cylinder cap
Reseat the pistons using a C-clamp or caliper expander (bleeder screws closed.)
Place new pads into calipers.
Replace calipers, wheels...
If you are careful to only open the bleeder after you have applied a LITTLE bit of pressure on the clamp, and you are careful to close the caliper bleeder screw as the piston bottoms in its bore, and BEFORE you release the C-clamp or caliper tool, you will not introduce air into the caliper requiring that the system be bled. You may want to cover the bleeder screw with a rag or use a tube from the bleeder to a container as it will squirt fluid when you open it under even a little pressure from the clamp.
Make sure to top up the master cylinder reservoir and don't let it empty whenever you open the system. If you do, you will introduce air.
Another cause of master cylinder failure is forcing the pedal to travel all the way to the floor when the cylinder is older and the pedal has not travelled so far in a long time. This can cause damage to the edges of the cup seals on the MC piston as they move over a part of the bore that may be corroded. It can also knock loose particles of rust that will abrade seals and clog passages. To avoid this, when you have installed your new pads and before you move the car, pump the brake pedal only about as far as it normally goes, then release and repeat until you have refilled the calipers with fluid and pushed the pistons out far enough that a relatively normal pedal is restored.
#10
Senior Member
Posts like a Northstar
Join Date: Dec 2005
Location: Indianapolis
Posts: 560
Likes: 0
Received 0 Likes
on
0 Posts
I just figured i was doing something to cause pressure problems in the antilock system.
Typically, the brakes would fail a few weeks after servicing.
My car is close to needing brake service, and I was just making sure,
Good idea with not letting the pedal travel to the floor.
Typically, the brakes would fail a few weeks after servicing.
My car is close to needing brake service, and I was just making sure,
Good idea with not letting the pedal travel to the floor.